background image

10

 

Installation and Servicing

SECTION 1 - GENERAL

1.1 INTRODUCTION

The

 i-mini C 

range of boilers are wall mounted, full sequence, 

automatic spark ignition, low water content, fanned flue, high 

efficiency, condensing, combination gas boilers.

Note. 

Due to the high efficiency of the boiler a plume of water 

vapour will form at the terminal during operation.

Central heating (CH) output is fully modulating with a range of:
24 

4.8 to 24.2kW

30 

6.1 to 24.2kW

Instantaneous domestic hot water (DHW) output is also fully 

modulating with a maximum of :
24 24.2kW
30 30.3kW
The boiler is supplied fully assembled with DHW plate heat 

exchanger, diverter valve, circulating pump, pressure gauge, 

safety valve and CH expansion vessel.

Variable CH and DHW temperature controls are fitted on the user 

control and the boiler features a DHW preheat facility.
The boiler includes as standard:

Automatic bypass

Boiler frost protection

Daily pump and diverter valve exercise

The boiler casing is of white painted mild steel with a white 

polymer front panel.
The boiler temperature controls are visible located in the control 

panel on the front of the boiler.
The heat exchanger is manufactured from cast aluminium.
The boiler is suitable for connection to fully pumped, sealed 

heating systems ONLY.  Adequate arrangements for completely 

draining the system by provision of drain cocks MUST be provided 

in the installation pipework.
Pipework from the boiler is routed downwards.

Data Plate

The boiler model and serial number can be located on the bottom of the 

boiler casing, shown in Frame 1 - Water & Gas Connection Diagram.

1.2 OPERATION

With no demand for CH, the boiler fires only when DHW is drawn 

off, or periodically for a few seconds without any DHW draw-off, in 

order to maintain the DHW calorifier in a heated condition.  This 

only occurs if pre-heat knob is in the ‘ON’ period.
When there is a demand for CH, the heating system is supplied at 

the selected temperature of between 30

o

C and 80

o

C, until DHW 

is drawn off.  The full output from the boiler is then directed via 

the diverter valve to the plate heat exchanger to supply a nominal 

DHW draw-off of 
24 

9.9 l/min at 35 

o

C temperature rise.

30 

12.4 l/min at 35 

o

C temperature rise.

The DHW draw off rate specified above is the nominal that the 

boiler flow regulator will give.  Due to system variations and 

seasonal temperature fluctuations DHW flow rates/temperature 

rise will vary, requiring adjustment at the draw off tap.
At low DHW draw-off rate the maximum temperature may exceed 

65ºC. 
The boiler features a comprehensive diagnostic system which 

gives detailed information on the boiler status when operating, 

and performance of key components to aid commissioning and 

fault finding.

1.3  SAFE HANDLING

This boiler may require 2 or more operatives to move it to its 

installation site, remove it from its packaging base and during 

movement into its installation location.  Manoeuvring the boiler 

may include the use of a sack truck and involve lifting, pushing and 

pulling.  
Caution should be exercised during these operations.
Operatives should be knowledgeable in handling techniques when 

performing these tasks and the following precautions should be 

considered:
•  Grip the boiler at the base.

•  Be physically capable.

•  Use personal protective equipment as appropriate, e.g. gloves, 

safety footwear.

During all manoeuvres and handling actions, every attempt should 

be made to ensure the following unless unavoidable  and/or the 

weight is light.
•  Keep back straight.

•  Avoid twisting at the waist.

•  Avoid upper body/top heavy bending.

•  Always grip with the palm of the hand.

•  Use designated hand holds.

•  Keep load as close to the body as possible.
•  Always use assistance if required.

1.4  OPTIONAL EXTRA KITS

•  Telescopic Horizontal Flue Terminal  (1000mm long)
•  Telescopic Horizontal Flue Terminal (600mm long)
•  Telescopic Horizontal B Pack Flue (600mm long) 

•  Flue Extension Ducts  (1000mm long)

•  Flue Extension Ducts  (2000mm long)

•  Flue Extension Ducts  (500mm long) 

24-up to 9m 

30-up to 8m

• 90

o

 Elbow Kit (maximum per installation). 

24-upto 6 elbows 

30-upto 6 elbows

• 45

o

 Elbow Kit (maximum per installation). 

24-upto 6 elbows 

30-upto 6 elbows

•  Roof Flue Kit (inc. vertical connector) (to a maximum of 7.5m)
•  Flue Finishing Kit
•  High Level Flue Outlet Kit
•  Balcony Flue Kit

•  Soffit Flue Kit

•  Adjustable Flue Support Bracket

•  Flue Deflector Kit
•  Raised Horizontal Flue Outlet Kit

•  Concentric Flue Screw Retaining Kit
•  Weather Collar
•  Stand-Off Kit
•  Condensate Pump Kit
•  DHW Expansion Vessel Kit
•  Weather Compensation Kit
•  PRV Wall Outlet Kit
•  Security Bracket Kit
•  Mechanical Timer (24hr) Kit

Содержание i-mini C24









































































Отзывы: