background image

ADS-RR(SR)-MA2H-DS-IG-EN

maestro.idatalink.com

Automotive Data Solutions Inc. © 2023

7

Mazda CX-3 TouChsCreen 2019

TROUBLESHOOTING TABLE

PROBLEM

SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

If anything is connected to the OBD2 or CAN wires of vehicle (programmer, 

throttle controller, insurance tracker, etc.) try unplugging it to see if gauges 

work.  If gauges work without it installed, call tech support for options.

Reset the RR.

CX-5 and Mazda3

No audio after installing new radio.  Factory radio no longer has sound.

Check 7.5 amp “AUDIO 2” fuse located under the hood.

The light on the Maestro is fl ashing 

RED ONCE

.

There is no fi rmware on the module. Flash the RR module using Weblink 

Desktop and log in. Do NOT use DEMO MODE.

The light on the Maestro is blinking 

RED TWICE

 and the radio 

IS

 turning on.

Ensure the 4-pin data cable is connected between the radio and the RR, and 

that it is plugged into the black port on the Maestro RR. The red and blue 

ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during 

the fl ash. Verify the radio’s serial number entered during the fl ash matches 

what is listed on the radio screen. This can be found in the settings of the 

radio, listed as Device Id, Device Number, or Serial Number.

The light on the Maestro is blinking 

RED TWICE

 but the radio is 

NOT

 turning 

on.

If installing a modular radio and it is not turning on, ensure the screen is 

secured and any trim pieces on the radio have been installed fully.  Not 

installing these fully will prevent radio from powering up and show a 2x red 

error as well.

Test red and yellow wires for DC voltage at radio using a multimeter.  Contact 

support if no voltage on red or yellow.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may 

take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999 
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio 

manufacturer’s website and look for any updates pertaining to your radio.

Содержание ADS-MRR2











































































































Отзывы: