ICPDAS LRA-900-E Скачать руководство пользователя страница 49

Страница: 49 / 55

LRA-900-E (Ethernet to LoRa Radio Modem) User Manual

Version 1.0.1

Page

：

Appendix A. Troubleshooting

A.1.

How do I restore the web password for the module to the factory default

password?

The instructions below outline the procedure for resetting the web password to the factory default

value.

Note:

Be aware that ALL settings will be restored to the factory default values after the module is reset.

Step 1

Locate the Init/Run switch that can be found on the right-hand side of the LRA-900-E module and

set it to the

"Init"

position. Reboot the module to

load factory default settings

including default

web password.

Step 2

Execute either the VxComm Utility or the eSearch Utility to search for any LRA-900-E modules

connected to the network. Verify that the LRA-900-E has been reset to the original factory default

settings. For example, the module should be shown as having the default IP address, which is

192.168.255.1.

Содержание LRA-900-E























































Результаты поиска

Содержание LRA-900-E

Отзывы:

Бренды по названию

Популярные бренды

ICPDAS LRA-900-E, Руководство пользователя

Результаты поиска

Содержание LRA-900-E

Отзывы:

Бренды по названию

Популярные бренды