ICP Electronics WAFER-7850 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 33

background image

51

4.11 Frequency/Voltage Control

CMOS Setup Utility – Copyright © 1984-2000 Award Software

Frequency/Voltage Control

   Auto Detect DIMM/PCI Clk   Disabled
   Spread Spectrum                 Disabled
   CPU Skew Adjust                Disabled
   SDRAM Skew Adjust          Disabled
   AGP Skew Adjust                Disabled
  CPU Host/PCI Clock          100/133MHz
   CPU Clock Ratio                 X 3

Item Help
-------------------------
Menu Level

↑↓←→

Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit

F1:General Help
F5:Previous Values F6:Fail-safe defaults F7:Optimized
Defaults

Auto Detect DIMM/PCI Clk

This item allows you to enable/disable auto detect DIMM/PCI Clock.

The choice: Enabled, Disabled.

Spread Spectrum

This item allows you to enable/disable the spread spectrum modulate.

The choice: Enabled, Disabled.

CPU Clock Ratio

This item allows you to select CPU clock ratio.

The choice: 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8.

52

4.12 Defaults Menu

Selecting “Defaults” from the main menu shows you two options
which are described below

Load Fail-Safe Defaults

When you press <Enter> on this item you get a confirmation
dialog box with a message similar to:

Load Fail-Safe Defaults (Y/N) ? N

Pressing ‘Y’ loads the BIOS default values for the most stable,
minimal-performance system operations.

Load Optimized Defaults

When you press <Enter> on this item you get a confirmation
dialog box with a message similar to:

Load Optimized Defaults (Y/N) ? N

Pressing ‘Y’ loads the default values that are factory settings for
optimal performance system operations.

«
...
24
25
26
27
28
...
»

Содержание WAFER-7850


































Отзывы:

Нет отзывов

Похожие инструкции для WAFER-7850

Analog Devices DC2605A

Бренд: Linear Страницы: 16

BLKDP55WG - P55 LG1156 MAX-16 GB DDR3 ATX Motherboard

Бренд: Intel Страницы: 88

Бренд: MSI Страницы: 94

Бренд: J&W Страницы: 36

Бренд: Zetex Страницы: 8

Бренд: IEI Technology Страницы: 131

Бренд: Avalue Technology Страницы: 75

Бренд: Supero Страницы: 80

Бренд: Nuvoton Страницы: 14

Бренд: ON Semiconductor Страницы: 19

Track bq27520EVM

Бренд: Texas Instruments Страницы: 22

Бренд: JETWAY Страницы: 47

Бренд: OLIMEX Страницы: 26

Бренд: Ublox Страницы: 2

Бренд: AOpen Страницы: 8

IN440 Micro-ATX

Бренд: trimond Страницы: 47

Бренд: IEI Technology Страницы: 12

Бренд: Rohm Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды