background image

 

 

1

 

               

WAFER-7850 

Pentium® III, Celeron with 

Single Port Ethernet, VGA, 3.5” SBC 

Ver 1.2

 

 

 
 
 
 
 
 
 

 

 
@Copyright 2000 
All Rights Reserved.  
Manual first edition August 21, 2000

 

The information in this document is subject to change without prior notice in 
order to improve reliability, design and function and does not represent a 
commitment on the part of the manufacturer. 
In no event will the manufacturer be liable for direct, indirect, special, incidental, 
or consequential damages arising out of the use or inability to use the product or 
documentation, even if advised of the possibility of such damages. 

This document contains proprietary information protected by copyright. All rights 
are reserved. No part of this manual may be reproduced by any mechanical, 
electronic, or other means in any form without prior written permission of the 
manufacturer. 

Trademarks

 

WAFER-7850 is registered trademarks of ICP Electronics Inc., IBM PC is a 
registered trademark of International Business Machines Corporation. Intel is a 
registered trademark of Intel Corporation. Award is registered trademarks of 
Award Software International, Inc. Other product names mentioned herein are 
used for identification purposes only and may be trademarks and/or registered 
trademarks of their respective companies.  

 

 

2

Contents

 

Contents

.............................................................................2 

Introduction

........................................................................5 

1.1   Specifications: .....................................................................................6 

1.2 What You Have........................................................................................7 

Installation

..........................................................................8 

2.1 WAFER-7850's Layout ...........................................................................9 

2.2 WAFER-7850's .....................................................................................10 

2.3 Clear CMOS Setup ................................................................................11 

2.4 BIOS Protection Setting ........................................................................12 

2.5 COM2 RS232 or RS422/485 Selection...............................................12 

2.6 CompactFlash Card Master/Slave Mode Setting .................................12 

2.7 LED Indications .....................................................................................14 

Connection

.......................................................................15 

3.1 Floppy Disk Drive Connector...............................................................15 

3.2 Ultra ATA33/66/100 IDE Disk Drive Connector...............................16 

3.3 Parallel Port............................................................................................17 

3.4 Serial Ports .............................................................................................17 

3.5 Keyboard Connector..............................................................................18 

3.6 USB Port Connector..............................................................................19 

Содержание WAFER-7850


































Отзывы: