background image

 

2

Table of Contents 

 

1.

 

Product Introduction................................................. 3

 

1.1

 

Common Features for IVC-100G/IVC-100...................................3

 

1.2

 

Common Features for IVC-200G/IVC-200...................................3

 

1.3

 

Common Features for IVC-120G/IVC-120...................................4

 

1.4

 

Special Features for IVC-100G/IVC-200G/IVC120G .....................4

 

1.5

 

Package Contents...................................................................4

 

1.6

 

System Requirements .............................................................4

 

1.7

 

Notes ...................................................................................5

 

2.

 

Hardware Connections & Settings ............................. 6

 

2.1

 

Illustration for Video Capture Card ............................................6

 

2.2

 

Connections to the Video Source ..............................................8

 

2.3

 

LED Jumper Settings...............................................................9

 

2.4

 

General Purpose Input Output (GPIO) Connections.................... 10

 

3.

 

Installation Procedures ........................................... 15

 

3.1

 

Driver Installation ................................................................ 15

 

3.2

 

Check for Installed Driver ...................................................... 18

 

4.

 

Demo Programs....................................................... 20

 

4.1

 

Video Image Preview for IVC-100G/100................................... 20

 

4.2

 

Video Image Preview for IVC-200G/200................................... 22

 

4.3

 

Video Image Preview for IVC-120G/120................................... 22

 

4.4

 

Recording the Captured Image ............................................... 25

 

5.

 

Uninstalling the Program ........................................ 27

 

Appendix A: Watch Dog Function of IVC-200G-WDT........... 28

 

Appendix B: PM-1056 Hardware Diagrams ......................... 30

 

Appendix C: How to Set SW1 of the PM-1056 when Using R20 
and R21 Version in One System.......................................... 35

 

 

Содержание IVC-100




































Отзывы: