ICP DAS USA PMC-523 Series Скачать руководство пользователя

Страница: 16 / 347

ICP DAS PMC-523x/PMC-224x/PMD Series User Manual

System Introduction

The

PMC-523x/PMC-224x(

ower

eter

oncentrator)/PMD(

ower

eter

Concentrator with

isplay) is an intelligent Power Meter Concentrator developed by

ICP DAS. It features various functions such as: power data management, logic control,

data logger and alarm notification functions. By using PMC/PMD solution; it is no

longer required to write programming for power management system. It takes only a

few clicks on the specific Web HMI Interface provided by

PMC/PMD

to complete

power management and logic control settings for monitoring the power meters

connected to the system.

This easy-to-use solution will dramatically reduce the labor

and cost spent on power monitoring and management system.

PMC-523x/PMC-224x

/PMD series products are including following models:

Product Series

PMC-523x

PMC-224x

Hardware

Dimension

117 mm x 126 mm x 58 mm

33 mm x 160 mm x 129 mm

Number of LAN Port

LAN port x 1

LAN port x

LCD

Detail Model Name

PMC-523x

PMC-2241

Support Ethernet

：

PMC-5231

PMC-2241

Support Ethernet / 3G

：

WCDMA 850/900/1800/1900 MHz

PMC-5231M-3GWA

Supported with optional

3G/4G modem

Support Ethernet / 4G

：

FDD LTE: B1/B3/B5/B7/B8/B20 MHz

PMC-5231M-4GE

Support Ethernet / 4G

：

FDD LTE: B1/B3/B8 MHz

TDD LTE: B38/B39/B40/B41 MHz

PMC-5231M-4GC

Product Series

PMD-2201

PMD-4201

Hardware

Dimension

213mm x 148mm x 44mm

291mm x 229mm x 54mm

Number of LAN Port

LAN port x 1

LCD

7" (16:9)

10.4" (4:3)

Support Ethernet

：

Yes

PMC-523x/PMC-224x

/PMD

allows connections to ICP DAS power meters via

RS-485 or Ethernet interface to read the power data of the devices measured by the

power meters; and then real-time record the power data in the data file.

PMC-523x/PMC-224x

/PMD

also provides data logger file auto send-back function;

together with PMC Data Server software or SCADA software, it allows collection and

Содержание PMC-523 Series




























































































































































































































































































































































Результаты поиска

Содержание PMC-523 Series

Отзывы:

Похожие инструкции для PMC-523 Series

Бренды по названию

Популярные бренды

ICP DAS USA PMC-523 Series, Руководство пользователя

Результаты поиска

Содержание PMC-523 Series

Отзывы:

Похожие инструкции для PMC-523 Series

Бренды по названию

Популярные бренды