ICP DAS USA PIO-D64 страница 41 Скачать руководство пользователя

Страница: 41 / 57

PIO-D64/PIO-

D64U User’s Manual ( Ver.1.

6, Mar. 2015, PMH-007-16 ) ----- 41

5.4.3 PIODIO_OutputWord



Description :

Send the 16 bits data to the specified I/O port.



Syntax :

void PIODIO_OutputWord(DWORD wPortAddr, DWORD

wOutputVal);



Parameter :

WPortAddr : [

Input

] I/O port addresses, please refer to function

PIODIO_GetConfigAddressSpace().

Only the low WORD is valid.

WOutputVal : [

Input

] 16-bit data send to I/O port.

Only the low WORD is valid.



Return:

None

5.4.4 PIODIO_InputWord



Description :

Obtain the 16 bits data from the specified I/O port.



Syntax :

DWORD PIODIO_InputWord(DWORD wPortAddr);



Parameter :

wPortAddr

: [

Input

] I/O port addresses, please refer to function

PIODIO_GetConfigAddressSpace().

Only the low WORD is valid.



Return:

16-bit data. Only the low WORD is valid.

ГК

Атлант

Инжиниринг

–

официальный

представитель

РФ

СНГ

+7(495)109-02-08 [email protected] www.bbrc.ru

Содержание PIO-D64


























































Результаты поиска

Содержание PIO-D64

Отзывы:

Похожие инструкции для PIO-D64

Бренды по названию

Популярные бренды

ICP DAS USA PIO-D64, Руководство пользователя

Результаты поиска

Содержание PIO-D64

Отзывы:

Похожие инструкции для PIO-D64

Бренды по названию

Популярные бренды