ICP DAS USA PEX Series Скачать руководство пользователя страница 31

Страница: 31 / 76

PEX/PIO/PISO-DA Series Card

Analog Output Boards

User Manual/ Ver. 3.1/ Oct. 2013/ PMH-0010-31/ Page: 31

2.6.9

Factory Software Calibration

t is recommended that a 16-bit A/D card is used to calibrate the PISO-DA/PIO-DA series cards.

The I-7000 series is a set of precise remote control modules and the I-7017 is an 8-channel

16-bit precision A/D module (24-bit sigma-delta A/D converter). Two I-7017 modules are

used for voltage output calibration and another two for current output calibration.

The steps required to calibrate the voltage for channel_n are as follows:

Step 1:

DaValue=0

Step 2:

Send the DaValue to channel_n on the PIO/PISO card

Step 3:

Measure the voltage of channel_n on the I-7017

If this value is >= -10 V, then go to Step 5

Step 4:

Increase the DaValue, then return to Step 2

Step 5:

MinV[n]=DaValue-1

Step 6:

DaValue=0x3fff

Step 7:

Send the DaValue to channel_n on the PIO/PISO card

Step 8:

Measure the voltage of channel_n on the I-7017

If this value is >= +10 V, then go to Step 10

Step 9:

Increase the DaValue, then return to Step 7

Step 10:

MaxV[n]=DaValue

Note: MinV[n] and MaxV[n] are described in

Sec. 2.6

ГК

Атлант

Инжиниринг

–

официальный

представитель

РФ

СНГ

+7(495)109-02-08 [email protected] www.bbrc.ru

Содержание PEX Series













































































Результаты поиска

Содержание PEX Series

Отзывы:

Похожие инструкции для PEX Series

Бренды по названию

Популярные бренды

ICP DAS USA PEX Series, Руководство пользователя

Результаты поиска

Содержание PEX Series

Отзывы:

Похожие инструкции для PEX Series

Бренды по названию

Популярные бренды