background image

PEX/PIO/PISO-DA Series Card 

Analog Output Boards

 

User  Manual/  Ver.  3.1/  Oct.  2013/  PMH-0010-31/  Page:  60 

 

6.3

 

  The I/O Address Map 

The I/O address for PEX-DAx, PISO-DAxU and PIO-DAxU series cards is automatically 

assigned by the ROM BIOS of the PC and provides Plug&Play capabilities for PIO/PISO 

series  cards.  The  PEX-DAx,  PISO-DAxU  and  PIO-DAxU  series  I/O  addresses  are 

mapped as follows: 

 

Table 6-3: Refer to 

Sec. 6.1.3

 for more information about wBase. 

Address 

Read 

Write 

wBase+0 

Reserved 

RESET\ control register 

wBase+2 

Reserved 

Aux control register 

wBase+3 

Aux data register 

Aux data register 

wBase+5 

Reserved 

INT mask control register 

wBase+7 

Aux pin status register 

Same 

wBase+0x2a 

Reserved 

INT polarity control register 

wBase+0xc0 

Read 8254-Counter0 

Write 8254-Counter0 

wBase+0xc4 

Read 8254-Counter1 

Write 8254-Counter1 

wBase+0xc8 

Read 8254-Counter2 

Write 8254-Counter2 

wBase+0xcc 

Read 8254 control word 

Write 8254 control word 

wBase+0xd4 

Read the Card ID 

Reserved 

wBase+0xe0 

Read the Low byte of D/I 

DA_0 chip select 

wBase+0xe4 

Read the High byte of D/I 

DA_1 chip select 

wbase+0xe8 

Read the Low byte of D/I 

(for PEX/PIO-DA only)

 

DA_2 chip select 

wBase+0xec 

Read the High byte of D/I 

(for PEX/PIO-DA only)

 

DA_3 chip select 

wBase+0xf0 

Read the Low byte of D/I 

(for PEX/PIO-DA only)

 

Write the Low byte of D/A 

wBase+0xf4 

Read the High byte of D/I 

(for PEX/PIO-DA only)

 

Write the High byte of D/A 

wBase+0xf8 

Read the Low byte of D/I 

(for PEX/PIO-DA only)

 

Write the Low byte of D/O 

wBase+0xfc 

Read the High byte of D/I 

(for PEX/PIO-DA only)

 

Write the High byte of D/O 

 

ГК

 

Атлант

 

Инжиниринг

 – 

официальный

 

представитель

 

в

 

РФ

 

и

 

СНГ

 

+7(495)109-02-08 [email protected] www.bbrc.ru 

Содержание PEX Series













































































Отзывы: