13
8
6. Hold the Console Assembly (91) near the Right Upright
(54).
Touch the Right Handrail to discharge any static.
Insert the end of the Wire Harness (98) into the hole in
the bottom of the Right Handrail (55) and out of the large
hole in the side. Next, Insert the end of the Wire Harness
through the two looped plastic ties.
Press the end of the Wire Harness (98) into the indicated
connector on the back of the Console Assembly (91).
The end of the Wire Harness should slide easily into
the connector and snap into place.
If it does not, turn
the end of the Wire Harness and try again.
IF THE CON-
NECTOR IS NOT INSERTED PROPERLY, THE CON-
SOLE MAY BE DAMAGED WHEN THE POWER IS
TURNED ON.
Plastic
Ties
Connector
91
55
98
54
5. Place the Left Handrail (56) on the Console Assembly
(91). Attach the end of the ground wire from the Console
Assembly to the indicated small hole in the Left Handrail
with the Silver Ground Screw (8).
Attach the Left Handrail (56) to the Console Assembly
(91) with two Console Screws (4), a Crossbar Screw (5),
and a Crossbar Star Washer (12).
Be careful not to
pinch the ground wire.
12
91
4
5
56
8
Ground Wire
Small
Hole
6
5
98
Measure your heart rate if desired.
Before using the hand-
grip pulse sensor, re-
move the sheets of
clear plastic from the
metal contacts. In addi-
tion, make sure that
your hands are clean.
To measure your heart rate,
stand on the foot
rails
and hold the metal contacts—
avoid moving
your hands
. When your pulse is detected, the
small heart symbol in the lower right display will
flash, one or two dashes will appear, and then
your heart rate will be shown.
For the most accu-
rate heart rate reading, continue to hold the
contacts for about 15 seconds.
When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
remove the key from the console. Keep the key in a
secure place. Then, switch the on/off switch to the
“off” position and unplug the power cord.
HOW TO USE A SPEED PROGRAM
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
11.
Select one of the four speed programs.
To select a speed pro-
gram, press the
Program Select button
repeatedly; “P-1,” “P-2,”
“P-3,” or “P-4” will ap-
pear in the priority dis-
play for a few seconds to show which program is
selected. The maximum speed setting of the se-
lected program will also appear in one of the dis-
plays for a few seconds.
Each program consists of 30 one-minute periods.
One speed setting is programmed for each period.
Note: The same speed setting may be pro-
grammed for two or more consecutive periods.
The profiles on the left side of the Program Select
button show how the speed of the walking belt will
change during the programs.
Press the Start button or the Speed increase
button to start the program.
When either button is pressed, the treadmill will
automatically adjust to the speed setting that is
programmed for the first period of the program.
Hold the handrails and begin walking.
When the first period ends, a series of tones will
sound. If a different speed setting is programmed
for the second period, the speed setting will flash
in one of the displays to alert you, and then
the
speed of the walking belt will change.
The pro-
gram will continue until all 30 periods are com-
pleted. The walking belt will then slow to a stop.
If the speed setting is too high or too low during
the program, you can manually override the setting
by pressing the Speed buttons. However,
when
the next period begins, the speed of the walk-
ing belt will change if a different speed setting
is programmed for the next period.
To stop the program, press the Stop button. The
time will begin to flash in one of the displays. To
restart the program, press the Start button or the
Speed increase button. The walking belt will begin
to move at 2 km/h. When the next period begins,
the speed of the walking belt will change if a differ-
ent speed setting is programmed for the next pe-
riod.
Follow your progress with the track and the
three displays.
See step 4 on page 12.
When you are finished exercising, remove the
key.
See step 6 on this page.
5
4
3
2
1
6
5
ETWE13906
WETL13906
7. Insert the slack in the Wire Harness (98) down into the
Right Upright (54). Then, tighten the two plastic ties
around the Wire Harness, and cut off the ends of the plas-
tic ties.
98
Plastic
Ties
54
7
Metal
Contacts
