background image

 

 

15 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

  

 

 

 

Icon

 

Fires Warranty Terms and Conditions

 

 

 

1.

 

All warranty claims are subject to manufacturer’s review and acceptance. 

 

 

 

2.

 

Icon Fires

 

warrants that it uses reasonable care and skill to ensure that its products 

are of reasonable quality. Icon Fires

 

will at it's cost and in it's sole discretion: (i) 

remedy any defect or fault in any product purchased; or (ii) replace any product 
in respect of which there is a defect or fault, during the warranty period, provided 
that written notice is given by the Purchaser to Icon Fires

 

of any such defect or 

fault in the product as soon as the Purchaser becomes aware of that fault or 
defect. All warranty claims must be returned to Icon Fires

 

for assessment with a 

receipt or other proof of payment. No warranty is given in respect of any glass 
contained in any product. 

 

 

 

3.

 

Icon Fires

 

has no liability to remedy any defect in a product or replace a product 

where the defect or fault is caused or contributed to by (i) the failure of the 
Purchaser to install the product according to specific installation instructions either 
supplied within each product box or carton or available on the Icon Fires

 

website 

or through the retailer representative; or (ii) use of the product in a manner or for a 
purpose for which it was not designed. 

 

 

 

4.

 

All site application or installation must reflect these procedures otherwise the 
product warranty will be considered void or will not take effect. 

 

Содержание Slimline SB500


















Отзывы: