RoIP GATEWAY
Installation guide
w
VE-PG2
Step1: Installation guide
q
Step2: Installation guide
w
1. Connects transceivers and LAN to the VE-PG2
MODE
DC
LAN
TRX1
TRX2
TRX3
IN
+
+
+
OUT
SW
ABC
1
2
3
4
5
MODE
DC
LAN
TRX1
TRX2
TRX3
IN
+
+
+
OUT
SW
ABC
q
w
t
y
e
To the [LAN] port
To the [TRX1] port
HUB
(192.168.0.2)
The [TRX1] port number: 21500
Connect the transceiver’s microphone connector and speaker jack.
NOTE: When using the repeater, connect the optional OPC-2074 to the repeater’s ACC connector.
Repeater’s rear panel
OPC-2074
ACC connector
[Area A]
[Area B]
Transceiver B
channel 2
Connect an Ethernet cable
Connect an Ethernet cable
VE-PG2
To the [TRX1] port
(192.168.0.3)
The [TRX1] port number: 21500
VE-PG2
To the [LAN] port
Connect the transceiver’s microphone connector and speaker jack.
Transceiver A
channel 2
Transceiver C
channel 10
Transceiver D
channel 10
NOTE: First, connect the transceiver
to the VE-PG2 using the optional
OPC-2073. Then turn ON the power
to the transceiver and the VE-PG2.
NOTE: First, connect the transceiver
to the VE-PG2 using the optional
OPC-2073. Then turn ON the power
to the transceiver and the VE-PG2.
Connect to the transceiver A’s speaker jack.
Connect to the transceiver C’s speaker jack.
CAUTION:
To connect the transceivers or repeaters, use only the following cables:
OPC-2073 (For the transceivers) or OPC-2074 (For the repeaters).
Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.
Using another cable, like an Ethernet cable may damage the VE-PG2,
transceivers or repeaters.
CAUTION:
To connect the transceivers or repeaters, use only the following cables:
OPC-2073 (For the transceivers) or OPC-2074 (For the repeaters).
Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.
Using another cable, like an Ethernet cable may damage the VE-PG2,
transceivers or repeaters.
MODE
DC
LAN
TRX1
TRX2
TRX3
IN
+
+
+
OUT
SW
ABC
Connect the optional OPC-2074 to
[TRX1], [TRX2] or [TRX3] only.
GROUND
GROUND
Turn the transceivers’ power ON,
and then set the transceiver A
volume to the 12 o’clock position.
Turn the transceivers’ power ON,
and then set the transceiver C
volume to the 12 o’clock position.
If you connect the VE-PG2 to an
IP network, instead of the hub as
shown in this illustration, you can
communicate anywhere through
the IP network.
r
Set External I/O (D-sub 25) port setting* to Ext. I/O 18 Output Low Voltage 2.
*The CS-FR5000 cloning software and OPC-1122U cloning cable are required when you set External I/O D-sub 25 port setting.
• A static (fixed) IP address must be set to the VE-PG2, and connects as figure below. (Refer to the Installation guide
q
for
details.)
• For the Unicast mode, after making the connections as illustrated below, set the VE-PG2 as described in the page to the
right.
• Refer to the Installation guide
q
for details of the Multicast mode and the Unicast modes.
• Connect the VE-PG2 according to steps
q
–
y
in the illustration below.
Bridge mode setting
2 Sets the VE-PG2 to the Bridge mode (Unicast mode)
1. ��P comm�nication mode setting�� setting
��P comm�nication mode setting�� setting
�P comm�nication mode setting�� setting
�� setting
setting
2. ��P net�or�� connection�����ranceiver 1 (���1)��setting
��P net�or�� connection�����ranceiver 1 (���1)��setting
�P net�or�� connection�����ranceiver 1 (���1)��setting
�����ranceiver 1 (���1)��setting
���ranceiver 1 (���1)��setting
��ranceiver 1 (���1)��setting
�ranceiver 1 (���1)��setting
��setting
setting
Set transceivers A and C AF volume to the 12 o�clock
�clock
clock
position.
3. �ransceiver setting
4. Ho� to comm�nicate
1
1
1
While holding down transceiver D�s [PTT] of Area B,
speak into the microphone at your normal voice level
to reply to transceiver B in Area A.
Release transceiver D�s [PTT] to receive.
While holding down transceiver B�s [PTT] in Area A,
speak into the microphone at your normal voice level
to call transceiver D in Area B.
Release transceiver B�s [PTT] to receive.
1
2
Bridge mode setting
Turn transceivers B and D power ON, and select the
same operating channel as transceivers A and C.
• Set the same channel for all the transceivers, to
communicate with transceivers A and C.
See the transceiver�s instruction manual when
setting the channel, if necessary.
(Example) I n t h e i l l u s t ra t i o n t o t h e l e f t , s e t
transceiver A and B (Area A) to channel
2, and transceiver C and D (Area B) to
channel 10.
2
This setting example refers to the connections in the far top
left illustration.
This setting example refers to the connections in the far top
left illustration.
2. �IP network connection�–�Tranceiver 1 (TR�1)� setting (Continued)
�IP network connection�–�Tranceiver 1 (TR�1)� setting (Continued)
IP network connection�–�Tranceiver 1 (TR�1)� setting (Continued)
�–�Tranceiver 1 (TR�1)� setting (Continued)
–�Tranceiver 1 (TR�1)� setting (Continued)
�Tranceiver 1 (TR�1)� setting (Continued)
Tranceiver 1 (TR�1)� setting (Continued)
� setting (Continued)
setting (Continued)
Click [Connect] in �IP network connection status�,
�IP network connection status�,
IP network connection status�,
�,,
and then confirm that �During transmit� appears in
�During transmit� appears in
During transmit� appears in
� appears in
appears in
�Status�.
Status�.
�..
2
2
3
This guide describes bridge and selective call mode
connection examples.
Read this guide after reading �Installation guide
q
�.
q
After making the connections as shown to the
left, turn transceivers A and C power ON, then
open the setting screen with your browser (see
Installation guide
q
).
w
Click �Operating mode� in the �Connection
�Operating mode� in the �Connection
Operating mode� in the �Connection
� in the �Connection
in the �Connection
�Connection
Connection
setting�, and select �Unicast mode� in the
�, and select �Unicast mode� in the
, and select �Unicast mode� in the
�Unicast mode� in the
Unicast mode� in the
� in the
in the
�Transceiver 1 (TR�1):� of �IP communication
Transceiver 1 (TR�1):� of �IP communication
� of �IP communication
of �IP communication
�IP communication
IP communication
mode setting�.
�..
e
Click [Save and Reboot].
Select [Unicast mode] in both Area A and Area B.
Select
Clic��
Clic��
Clic��
Enter
Confirm
The dialog shown below appears, and then click [OK].
NO�E:
�IP network connection� is initiali�ed after
�IP network connection� is initiali�ed after
connection� is initiali�ed after
� is initiali�ed after
is initiali�ed after
changing �IP communication mode setting�.
�IP communication mode setting�..
Save the VE-PG2 setting as a setting file, if
necessary.
Refer to the instruction manual (PDF file:
Download from the Icom web site) for details.
Approximately 30 seconds after clicking [OK], move
the mouse pointer to [BACK] and click. After system
reboots, the setting screen will open.
q
Click �Transceiver 1 (TR�1)� in �IP network
�Transceiver 1 (TR�1)� in �IP network
Transceiver 1 (TR�1)� in �IP network
� in �IP network
in �IP network
�IP network
IP network
connection setting� in the �Connection setting�.
� in the �Connection setting�.
in the �Connection setting�.
�Connection setting�.
Connection setting�.
�..
w
Input the Connection IP address in the �IP network
�IP network
IP network
connection�.
�..
(Example) Input �1�2.1��.0.3� to VE-PG2s in Area
�1�2.1��.0.3� to VE-PG2s in Area
1�2.1��.0.3� to VE-PG2s in Area
� to VE-PG2s in Area
to VE-PG2s in Area
A, and �1�2.1��.0.2� to VE-PG2s in
�1�2.1��.0.2� to VE-PG2s in
1�2.1��.0.2� to VE-PG2s in
� to VE-PG2s in
to VE-PG2s in
Area B illustrated to the left.
e
Click [Save].
Clic��
�Connection IP address� for Area A �� �1�2.1��.0.3�
Connection IP address� for Area A �� �1�2.1��.0.3�
� for Area A �� �1�2.1��.0.3�
for Area A �� �1�2.1��.0.3�
�1�2.1��.0.3�
1�2.1��.0.3��
�Connection IP address� for Area B �� �1�2.1��.0.2�
Connection IP address� for Area B �� �1�2.1��.0.2�
� for Area B �� �1�2.1��.0.2�
for Area B �� �1�2.1��.0.2�
�1�2.1��.0.2�
1�2.1��.0.2��
Click �Connect� in both Area A and Area B.
�Connect� in both Area A and Area B.
Connect� in both Area A and Area B.
� in both Area A and Area B.
in both Area A and Area B.
Confirm �Status� in both Area A and Area B.
�Status� in both Area A and Area B.
Status� in both Area A and Area B.
� in both Area A and Area B.
in both Area A and Area B.
