ABOUT THE FIRMWARE
The firmware may be upgraded when the functions and
specifications of the VE-PG2 are improved.
If the VE-PG2 is initialized after upgrading, set the
VE-PG2�s IP address, operating mode, etc. again.
�s IP address, operating mode, etc. again.
s IP address, operating mode, etc. again.
See the VE-PG2 instruction manual for details.
SPECIFICATIONS
• Power supply requirements : DC 12 V ±10%, Maximum 500 mA
• Usable environment
: Temperature range: 32
ƒ
to
104
ƒ
(0
ç
to 40
ç
)
Humidity range: 5% to 95%
•
Dimensions
: 7.48(W) × 1.57(H) × 5.51(D) in
(190(W) × 40(H) × 141(D) mm)
• Weight
: approximately 1.19 lb (540 g)
All stated specifications and design are subject to
change without notice or obligation.
PANEL DESCRIPTION
[POWER]
[LAN]
[VoIP]
[TRX1]–[TRX3]
[EXT]
Lights
• While the AC adapter is
connected. (green)
• New firmware is available.
(orange)*
4
While the Ethernet cable
is connected. (green)
In the bridge mode, when
exter nal devices such as
transceivers, repeaters are
connected. (green)
• While the connected
transceivers are receiving.
(green)*
2
• While the connected
transceivers are transmitting.
(red)*
2
• In the bridge mode, when the [IN] or
[OUT] port are enabled.*
2
• In the selective call mode, while
communicating with transceivers,
repeaters or other external devices.*
2
Red
: [OUT] port is used.
Green : [IN] port is used.
Orange : [OUT] and [IN] ports are used.
While the VE-PG2 upgrades the firmware, all LEDs light. (orange).
Blinks
Hold down [INIT] for 5 seconds
(green/orange alternately)*
1
to
initialize the VE-PG2.
• While data is sent or
received (green)
• While the [LAN] port
link down. (red)*
3
• When a PING transmitting
problem occurs. (red/
green alternately)*
3
In the selective call mode,
while sending RoIP data.
(green)
–
–
OFF
The AC adapter is disconnected. While the Ethernet
cable is disconnected.
• In the bridge mode, when
external devices such as
transceivers, repeaters are
disconnected.
• In the selective call mode,
while not sending RoIP data.
While the connected
transceivers are not
transmitting or receiving.
• When the [IN] or [OUT] port is
disabled in bridge mode.
• While not communicating with
transceivers, repeaters or other
external devices in the in selective
call mode.
POWER
VoIP
TRX1
TRX2
TRX3
LAN
EXT
[POWER] [LAN] [VoIP] [TRX1] [TRX3]
[EXT]
*
1
See “INITIALI�ING THE VE-PG2” for details.
“INITIALI�ING THE VE-PG2” for details.
INITIALI�ING THE VE-PG2” for details.
” for details.
for details.
*
2
When “Emergency notice” is selected for devices, in the Bridge mode, the LEDs do not light.
“Emergency notice” is selected for devices, in the Bridge mode, the LEDs do not light.
Emergency notice” is selected for devices, in the Bridge mode, the LEDs do not light.
” is selected for devices, in the Bridge mode, the LEDs do not light.
is selected for devices, in the Bridge mode, the LEDs do not light.
*
3
The LEDs blink only when “Abnormal condition monitor” is selected.
“Abnormal condition monitor” is selected.
Abnormal condition monitor” is selected.
” is selected.
is selected.
*
4
Set the DNS server and default gateway IP addresses for the VE-PG2 to automatically confirm if a firmware upgrade is available through the internet.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A-6838W-1US
Printed in Japan
© 2010 Icom Inc.
■
Top panel
■
LED indicator
q
w
e
r
t
o
i
u
y
!0
■
Rear panel
■
Bottom panel
INITIALI�ING THE VE-PG2
If you cannot access to the VE-PG2 setting screen, you can
initialize the VE-PG2 by holding down [INIT] for 5 seconds.
• Set the VE-PG2�s IP address, operating mode, etc. again.
�s IP address, operating mode, etc. again.
s IP address, operating mode, etc. again.
• Disconnect all cables from the VE-PG2, and then connect
the AC adapter to the VE-PG2 again.
Confirm that the [POWER] indicator lights green, and then
insert a thin rod into the [INIT] hole and holding down the
switch inside for 5 seconds.
VE-PG2 bottom view
[INIT]
Operation
LEDs status condition
POWER
LAN
VoIP
TRX1
TRX2
TRX3
EXT
q
Disconnect all cables from the VE-PG2, and then connect the AC
adapter to the VE-PG2.
G
w
Hold down [INIT] for 5 seconds.
• Blinks green/orange alternately.
G/O
e
When all LEDs light orange, the VE-PG2 is initialized.
O
▼
G
▼
O
▼
O
▼
G
O
▼
▼
▼
▼
O
▼
▼
▼
▼
G
O
▼
▼
▼
▼
O
▼
▼
▼
▼
O
▼
▼
▼
▼
O
▼
▼
▼
▼
[LED condition]
: LEDs are OFF
: Lights green
: Lights orange
: Blinks green
: Blinks orange
: Blinks green/orange alternately
G
O
G/O
G
O
q
MODE button [MODE]
Hold down for 5 seconds to automatically upgrade the
firmware through the internet.
w
DC jack [DC]
Connect the supplied AC adapter.
e
Ground terminal [GND]
Connect this terminal to ground to prevent electrical
shocks, TVI, BCI and other problems.
r
Ethernet port [LAN]
Connect the Ethernet cable.
t
Transceivers or repeaters connection ports
[TRX1]/[TRX2]/[TRX3]
Connect the transceivers or repeaters using with
the optional connection cable (OPC-2073: For the
transceivers, OPC-2074: For the repeaters).
y
Input terminal [IN]
Connect to the external device�s output port.
�s output port..
u
Output terminal [OUT]
Connect to the external device�s input port.
�s input port..
i
Switch terminal [SW]
Connect a control wire from an external device for input
to the VE-PG2.
o
A/B/C terminals [A]/[B]/[C]
Connect a control wire to an external device.
• Selectable the switch either [A] to [C] or [B] to [C].
!0
INITIALIZING button [INIT]
Hold down for 5 seconds to initialize the VE-PG2.
(Projections not included.)
(Without the AC adapter.)
TERMINAL INSTALLATION AND CONNECTION
Use a
1
/
32
inch (1.2 mm) (d) terminal,
13
/
32
to
7
/
16
inch (10 to 11 mm) for terminal length.
Crimp on pin terminal
Cable (Single line: AWG22 to 16)
When inserting the cable
When removing the cable
Flat-blade
[IN]/[OUT]/[SW]/[A]/[B]/[C] terminals
13
/
32
in (10 mm)
For secure connections, refer to the description to the right
before connecting the cables to the [IN]/[OUT]/[SW]/[A]/
[B]/[C] terminals.
Use the crimp on pin terminals, if necessary.
Turn OFF the VE-PG2�s power before connecting the cable.
�s power before connecting the cable.
s power before connecting the cable.
• Use the proper size crimp tool.
