background image

|SAT100M

1

NETWORK SETTING

SATELLITE PTT

When the transceiver is connected to the network devices, change the static IP address.

Before using the transceiver, setting a static IP address to the antenna unit and the main unit with EX-4241Utility 

for IC-SAT100M.

This manual shows system requirements and how to use the software.

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, 

Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries.

Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.

All other products or brands are registered trademarks or trademarks of their respective holders.

System requirements

The following hardware and software are required:

Operating System (OS)

 • Microsoft Windows 10 (32/64bit)

 • Microsoft Windows 8.1 (32/64bit)* 

*Except for Microsoft Windows RT.

 

L

The instructions are based on using Microsoft 

Windows 10.

Cables (Purchase separately)

 • OPC-2357 PROGRAMMING CABLE

Operation note

 • The contents of this sheet, the software associated with the EX-4241, and the appearance of the EX-4241 are 

all subject to change without notice.

 • The displays, indications, or operations may differ slightly, depending on your system settings, type of OS, and 

its service pack level.

Table of contents

System requirements................................................. 1
Operation note ........................................................... 1
Installing the EX-4241 ............................................... 2
Before connecting the OPC-2357 to the PC.............. 3
Connecting with PC ................................................... 3

Editing Network Setting ............................................. 4

 

D

About basic operation ........................................ 5

 

D

COM Port Searching .......................................... 5

Connecting with the network devices ........................ 6
Connecting the VE-PG4 ............................................ 7

 

D

Connecting the IC-SAT100M to the IP Network ... 8

 

D

Entering the Destination Settings .................... 10

Содержание IC-SAT100M











Отзывы: