background image

A-6602H-2EX-

y

 

Printed in Japan

© 2007–2014 Icom Inc.

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

Printed on recycled paper with soy ink.

The IC-A210/IC-A210E mates with a Card edge connector 
in the rack mount. Assemble the Card edge connector as 
follows.

D

 Card edge connector assembly

q

  Strip 4 mm (0.16

) from each wire for the card edge 

connector.

w

  Tin the leads of the wires.

e

  Pass the wires through a short length of 13 mm (0.5

heat shrink tubing.

r

 Solder the leads to the contact terminals.

t

  Cover the soldered terminals with the heat shrink tubing 

and heat until they are fixed in place.

y

  Cover the unused terminals with the heat shrink tubing 

10 mm (0.4

), then heat them to prevent shorting.

D

 Polarizing key

Before installing the Connector into the mounting bracket, 
check the polarizing key position between contacts 8 and 
9. Refer to Connector front view in 

CONNECTOR IN-

FORMATION.

,

 CARD EDGE CONNECTOR ASSEMBLY

Check the following points after transceiver installation.

- Polarity of the power supply.

NO

 interference caused to other equipment.

NO

 noise or interference from other equipment.

- VSWR is less than 2.5:1.
-  Communication capability on both the highest and lowest 

communication frequencies, if possible.

.

 OPERATION CHECK

Connect the GPS receiver’s input/output terminals as below table.

INFORMATION FOR GPS RECEIVER CONNECTION

 

GPS receiver’s terminal

 

Connector

 

D-sub connector

 

Input terminal 

pin 1 

pin 3

 

Output terminal 

pin 2 

pin 10

L-type BNC 
connector
(Purchase locally, if required)

Coaxial 
connector

BNC-LP

r

 

BNC-LP

Nut

Antenna cable clip

Self-crimping nut

Washer

C-shaped ring 

!2 

Screws

!0 

Screw

Screws Bind UNC

!5 

Polarizing key

Mounting

  bracket

Card edge connector 

!1 

Crimp nuts

Mounting

  bracket

 

When using the MB-53

!8 

Voltage sticker 

     (IC-A210E only)

MB-53

⁄0 

MOUNTING BRACKET ASSEMBLY

D

 Notes for making the mounting hole

The IC-A210/IC-A210E can be mounted securely in the 
supplied mounting bracket.

Remember to allow adequate space for installation of cables 
and connectors.

When installing 2 or more transceivers in a stack, the mount-
ing trays should be 1.3 mm 

(0.05

)

 apart.

The mounting bracket has 0.6 mm 

(0.024

)

 dimples in the 

top, bottom, and both sides for proper spacing.

Mark and cut the mounting holes.

To support the mounting bracket, the rear mounting bosses 
should be attached to the airframe.

⁄1

 MARKING MOUNTING HOLES

D

 Mounting bracket dimensions

160 mm; 6

 

5

16

33 mm; 1

 

5

16

260 mm; 10

 

1

4

D

 Front panel dimensions

160 mm; 6

 

5

16

34 mm;

 1

 

11

32

MEMO

DUAL

GRP

RCL

MEM

OFF

VOL

PUSH

TEST

COMM

DUAL EC

iA210

  Allow space for the front panel as shown above (illustration: IC-A210).

D

 Template

  Cut out dimensions for the mounting bracket as follows.

160 mm; 6

 

5

16

33 mm;

 1

 

5

16

D

 Transceiver installation

q

  Remove the front panel from the main unit, using a 

3

32

 

allen wrench, then carefully disconnect the flat cable from 
the front panel. 

(Fig. 1)

w

  Insert a

 

3

32

″ 

allen wrench into the hole of the main unit 

and unscrew the inside lock screw until the in-side metal 
catch touches the chassis hole. 

(Fig. 2)

 

•  

Use the metal catch located on bottom side of the transceiver 
when installing into the existing mounting bracket with MB-113 .

Use when installing with 
the original mounting bracket.

Main unit front view

Using this hole when 
installing with the MB-113.

e

  Rotate the lock screw clockwise 4 revolutions 

(Fig. 3)

, and 

then rotate counterclockwise a quarter revolution. 

(Fig. 4)

r

  Insert the main unit (transceiver) into the mounting 

bracket. 

(Fig. 5)

t

  Screw the lock screw to fix the main unit (transceiver) to 

the bracket. 

(Fig. 6)

y

  Connect the flat cable. 

(Fig. 7)

u

  Attach the front panel and re-screw the allen bolts 

(Fig. 7)

.

D

 Transceiver removal

The IC-A210/IC-A210E is easily removed from the mounting 
bracket, if required.

q

  Remove the front panel from the main unit, using a 

3

32

 

allen wrench, then disconnect the flat cable from the front 
panel.

w

  Insert a 

3

32

″ 

allen wrench into the hole of the main unit 

and unscrew the inside lock screw.

e

 Slowly pull the transceiver out from the mounting bracket.

r

 Connect the flat cable to the front panel.

t

 Attach the front panel and tighten the allen screws.

Fig. 1

Fig. 6

Fig. 5

Fig. 7

Fig. 1

Fig. 6

Fig. 5

Fig. 7

Clockwise: For installation.
Counterclockwise: For removal.

CAUTION:

Treat the flat cable with care  
when disconnecting it.

CAUTION:

Treat the flat cable with care 
when connecting it.

Clockwise: For installation.
Counterclockwise: For removal.

Surface

Flat cable

Fig. 2

Fig. 4

Fig. 3

Screw 4 revolutions

Unscrew a quarter 
revolution 

• Metal catch position

Good!

Bad

Metal catch

Surface

The flat cable

Fig. 2

Fig. 4

Fig. 3

Screw 4 revolutions

Unscrew a quarter 
revolution 

• Metal catch position

Metal catch

Flat cable

Good!

Bad

Flat cable

⁄2

 MOUNTING TO THE BRACKET

CAUTION:  

Tr e a t   t h e   f l a t   c a bl e   w i t h   c a r e   w h e n 
disconnecting it to avoid possible damage.

 

 Improper care disconnecting the cable can 
cause    damage  and  result  in  severe  non-
warranty repair.

CAUTION:  

Make sure that the flat cable between the 
transceiver  and  front  panel  is  securely 
connected. The transceiver may not function 
properly  when  loose  or  when  a  wrong 
connection is made.

   

 Improper care installing the cable can cause  
damage and result in severe non-warranty 
repair.

Отзывы: