Icom IC-F610, Руководство по обслуживанию

Страница: 14 / 40

M
REQUIRED TEST EQUIPMENT
EQUIPMENT GRADE AND RANGE EQUIPMENT GRADE AND RANGE
DC power supply
Output voltage : 13.6 (13.2) V DC
Current capacity : 20 A or more
Audio generator
Frequency range : 300–3000 Hz
Measuring range : 1–500 mV
FM deviation meter
Frequency range : DC–600 MHz
Measuring range : 0 to
±
10 kHz
Attenuator
Power attenuation : 50 or 60 dB
Capacity : 100 W
Frequency counter
Frequency range : 0.1–600 MHz
Frequency accuracy : ±1 ppm or better
Sensitivity : 100 mV or better
Standard signal
generator (SSG)
Frequency range : 0.1–600 MHz
Output level : 0.1 µV to 32 mV
(–127 to –17 dBm)
Digital multimeter Input impedance : 10 M
Ω
/V DC or more AC millivoltmeter Measuring range : 10 mV to 10 V
RF power meter
Measuring range : 1–75 W
Frequency range : 100–800 MHz
Impedance : 50
Ω
SWR : Better than 1.2 : 1
Oscilloscope
Frequency rang : DC–20 MHz
Measuring range : 0.01–20 V
External speaker
Input impedance : 4
Ω
Capacity : 7 W or more
SECTION 5 ADJUSTMENT PROCEDURES
5 - 1
5-1 PREPARATION
When adjusting IC-F610, IC-F620 or IC-F621, one of the following optional adjustment software and
JIG CABLE
(modified
OPC-1122 CLONING CABLE ; see illustration page 5-5) are required.
• CS-F500 ADJ (Rev. 2.0 or later): [CONV], [BIIS] versions:
• CS-F600(MPT) ADJ (Rev. 1.0 or later): [MPT] version
• CS-F620TR ADJ (Rev. 1.0 or later): [LTR] version
M
SYSTEM REQUIREMENTS
• Microsoft
®
Windows
®
95/98/Me [CONV], [MPT], [BIIS]
Microsoft
®
Windows
®
98/Me/XP [LTR]
• RS-232C serial port (D-sub 9 pin)
M
ADJUSTMENT SOFTWARE INSTALLATION
q
Quit all applications when Windows is running.
w
Insert the CD into the appropriate CD drive.
e
Double-click the “Setup.exe” contained in the adjustment
software folder in the CD drive.
r
The “Welcome to the InstallShield Wizard for adjustment
software will appear. Click [Next>].
t
The “Choose Destination Location” will appear. Then click
[Next>] to install the software to the destination folder.
y
After the installation is completed, the “InstallShield Wiz-
ard Complete” will appear. Then click [Finish].
u
Eject the CD.
i
The adjustment software icon appears on the desk top
screen.
M
BEFORE STARTING SOFTWARE ADJUSTMENT
Program the adjustment frequencies into the transceiver
using with the cloning software before starting the software
adjustment. Otherwise, the transceiver can not start software
adjustment.
CAUTION!: BACK UP the originally programmed mem-
ory data in the transceiver before program-
ming the adjustment frequencies.
When program the adjustment frequencies into
the transceiver, the transceiver’s memory data
will be overwritten and lose original memory
data at the same time.
M
STARTING SOFTWARE ADJUSTMENT
q
Connect the transceiver and PC with the JIG CABLE.
w
Turn the transceiver power ON.
e
Boot up Windows, and click the adjustment soft ware icon
on the desk top screen.
r
Click ‘Connect’ on the adjustment software window, then
appears the transceiver’s adjustment screen.
t
Set or modify adjustment data as desired.
Microsoft and Windows are registered trademarks of
Microsoft Corporation in the U.S.A. and other countries.
• ADJUSTMENT FREQUENCY LIST
CH FREQUENCY CONDITION
1
400.000 MHz [L]
440.000 MHz [M]
480.000 MHz [H]
TX power
Mode : Low1
: Wide
2
400.000 MHz [L]
440.000 MHz [M]
480.000 MHz [H]
TX power
Mode : Low2
: Wide
3
400.000 MHz [L]
440.000 MHz [M]
480.000 MHz [H]
TX power
Mode : High
: Wide
4
415.000 MHz [L]
465.000 MHz [M]
500.000 MHz [H]
TX power
Mode : Low1
: Wide
5
415.000 MHz [L]
465.000 MHz [M]
500.000 MHz [H]
TX power
Mode : Low1
: Narrow
6
415.000 MHz [L]
465.000 MHz [M]
500.000 MHz [H]
TX power
Mode
CTCSS
DTCS code : Low1
: Wide
: 88.5 Hz
: 007
7
430.000 MHz [L]
490.000 MHz [M]
520.000 MHz [H]
TX power
Mode : Low1
: Wide
8
430.000 MHz [L]
490.000 MHz [M]
520.000 MHz [H]
TX power
Mode : Low1
: Narrow