background image

MAINTENANCE

24

9

CLONING

23

8

Optional UT-96/ UT-105/ UT-108/ UT-109/
UT-110/ UT-111 and UT-113 installation

You can install one of the following optional signaling units in the
transceiver. UT-96 2TONE/5TONE UNIT, UT-105 SmarTrunk

(TM)

Logic

Board

, UT-108 DTMF DECODER UNIT, UT-109/ UT-110 SCRAM-

BLER UNIT

, UT-111 TRUNKING BOARD or UT-113 MAN DOWN

UNIT

.

q

Remove the optional connecter access cover (named 2251 OPT
sheet).

• Insert a screwdriver into the

hollow of the chassis, then lift
and take away the cover.
(The cover can not be used
again.)

w

Attach the desired optional unit. Insert the connector tightly to

avoid a bad contact.

e

Remove the paper backing of 2251 OPT sheet supplied as an
accessory.

r

Attach the new 2251 OPT sheet to the service window.

t

Program the necessary infor-
mation with the cloning soft-
ware before operation.
Please ask your dealer or
system operator for details.

w

e

r

q

Cloning

Cloning allows you to quickly and easily transfer the programmed
contents from one transceiver to another transceiver; or data from
PC to a transceiver using the optional CS-F3G 

CLONING SOFTWARE

.

D

D

Transceiver-to-transceiver cloning

q

Connect the optional OPC-474 

CLONING CABLE

to the [SP] jack

of the master and slave transceivers.

• The master transceiver is used to send data to the slave trans-

ceiver.

w

While pushing [P0] and [

Y

Y

], turn the transceiver’s power on to

enter cloning mode (For both the master transceiver and slave
transceiver).

• “CLONE” appears and the transceiver enters the clone standby

condition.

e

Push [PTT] on the master transceiver.

• “CLOUT” appears in the master transceiver’s display.
• “CL IN” appears automatically in the slave transceiver’s display.
• When cloning is finished, “CLONE” appears in the master trans-

ceiver’s display.

NOTE: DO NOT

push the [PTT] on the slave transceiver during

cloning. This will cause a cloning error.

r

When cloning is finished, turn power off, then on again to return
to normal operation.

NOTE:

Transceiver-to-transceiver cloning can not be done

between 40CH version and 100CH version, or CPU Rev.1.

and Rev.2.0.

• While pushing [P3] and [

Y

Y

], turn the transceiver’s power on to enter

CPU version check mode. CPU revision is displayed (“100CH” display
for 100CH version only).

Содержание IC-F3GS

















Отзывы: