Icom IC-F2610, Руководство по обслуживанию

Страница: 18 / 46

5 - 5
P
2
OUTPUT
POWER
FM
DEVIATION
DTCS WAVE
FORM AND
DEVIATION
CTCSS
TONE
DEVIATION
24 W [25 W]
10 W [10 W]
10 W [25 W]
5 W [10 W]
2.5 W
±4.0 kHz [W]
±2.0 kHz [N]
±0.7 kHz [W]
±0.35 kHz [N]
±0.7 kHz [W]
±0.35 kHz [N]
Connect an RF power meter to
the antenna connector.
Connect an FM deviation
meter to the antenna connec-
tor through an attenuator.
Connect an FM deviation
meter with an oscilloscope to
the antenna connector through
an attenuator.
Connect an FM deviation
meter to the antenna connec-
tor through an attenuator.
• Operating freq. : 400.000 MHz [L]
440.000 MHz [M]
490.000 MHz [H]
465.000 MHz
[[EUR-13], [[EUR-02], [EUR-72] only
• Enter Initial Set Mode No. 6.
Refer to page 5-2 for details.
• Operating freq. : 400.000 MHz [L]
440.000 MHz [M]
490.000 MHz [H]
• Enter Initial Set Mode No. 4.
Refer to page 5-2 for details.
• Connect an audio generator to the
microphone connector and set as:
1 kHz/35 mV
• Set an FM deviation meter as:
HPF : OFF
LPF : 20 kHz
De-emphasis : OFF
Detector
: (P–P)/2
• W/N setting : Wide
• W/N setting : Narrow
• Operating freq. : 415.000 MHz [L]
465.000 MHz [M]
505.000 MHz [H]
• Enter Initial Set Mode No. 4.
Refer to page 5-2 for details.
• No AF signals are applied to the micro-
phone connector.
• Set an FM deviation meter as:
HPF : OFF
LPF : 20 kHz
De-emphasis : OFF
Detector
: (P–P)/2
• W/N setting : Wide
• DTCS code : 007
• W/N setting : Narrow
• Operating freq. : 415.000 MHz [L]
465.000 MHz [M]
505.000 MHz [H]
• Enter Initial Set Mode No. 4.
Refer to page 5-2 for details.
• No AF signals are applied to the micro-
phone connector.
• Set an FM deviation meter as:
HPF : OFF
LPF : 20 kHz
De-emphasis : OFF
Detector
: (P–P)/2
• W/N setting : Wide
• CTCSS tone freq. : 88.5 Hz
• W/N setting : Narrow
P
2
P
1
P
3
P
1
P
2
P
3
Rotate volume
control while
pushing .
Rotate volume
control while
pushing .
Rotate volume
control while
pushing .
Rotate volume
control while
pushing .
Rotate volume
control while
pushing .
Rotate volume
control while
pushing .
Rotate volume
control while
pushing .
Set to flat wave
form
5-5 TRANSMITTER ADJUSTMENT
ADJUSTMENT ADJUSTMENT CONDITIONS
VALUE ADJUST
MEASUREMENT
METHOD
ADJUSTMENT
1
1
2
1
2
3
1
2
NOTE: When the RF output power cannot be set with this proce-
dure, cloning may be necessary to cancel the output power
setting.
[L]: [L-band (400–430 MHz)], [M]: [M-band (440–490 MHz)], [H]: [H-band (490–520 MHz)], [W]: 25 kHz, [N]: 12.5 kHz