Icom IC-F24/S, Дополнение к руководству по обслуживанию, Страница: 64 / 85

5 - 8
5-3 TRANSMIT ADJUSTMENT
5-3-1 TRANSMIT ADJUSTMENT FOR OTHER THAN IC-F26-L
1) Select an adjustment item using cursor or [
↑
] / [
↓
] keys of the PC’s keyboard.
2) Set or modify the adjustment value as specifi ed using [
←
] / [
→
] keys of the PC’s keyboard, then push the [ENTER] key.
ADJUSTMENT ADJUSTMENT CONDITION OPERATION
ADJUSTMENT
ITEM
VALUE
TRANSMIT
OUTPUT
POWER
-Preparation- 1 <For IC-F24S/F25S/F26S only>
Clone the "ADJ CH FREQ_TXPWR.icf" into the transceiver.
–
• Connect an RF Power Meter to the
antenna connector. – –
-Adjustment-
Hi 2 • CH. (16CH/2CH) : CH.3/CH.4
• Transmitting
1) Adjust the transmit output power
using [
←
] / [
→
] keys on the PC’s
keyboard.
2) Push the [ENTER] key to store the
adjust value.
[Power (Hi)] 4.0 W
L2 3 • CH. (16CH/2CH) : CH.4/CH.3
• Transmitting
[Power (L2)] 2.0 W
L1 4 • CH. (16CH/2CH) : CH.5/CH.1
• Transmitting
[Power (L1)] 1.0 W
DEVIATION
-Preparation- 1 <For IC-F24S/F25S/F26S only>
Clone the "ADJ CH AudioMOD.icf" into the transceiver.
• Connect a Modulation Analyzer
t o t h e a n t e n n a c o n n e c t o r
through an Attenuator.
• Set the Modulation Analyzer as;
HPF
: OFF
LPF : 20 kHz
De-emphasis : OFF
Detector : (P-P)/2
– –
2 • Connect an Audio Generator
to the MIC line through the JIG
cable.
• Set the Audio Generator as;
Modulation : 1 kHz
Level : 40 mV rms
Wave form : Sine wave
– –
-Adjustment-
NARROW 3 • CH. (16CH/2CH) : CH.6/CH.1
• Transmitting
1) Adjust the deviation using [
←
] / [
→
]
keys on the PC’s keyboard.
2) Push the [ENTER] key to store the
adjust value.
[MOD N]
±2.05–2.15
kHz
WIDE 4 • CH. (16CH/2CH) : CH.7/CH.3
• Transmitting
[MOD Ratio]
±4.05–4.15
kHz
MIDDLE* 5 • CH. (16CH/2CH) : CH.8/CH.2
• Transmitting
[MOD Ratio]
±3.15–3.25
kHz
MODULATION
BALANCE
-Preparation- 1 <For IC-F24S/F25S/F26S only>
Clone the "ADJ CH ToneMOD.icf" into the transceiver.
• Connect a Modulation Analyzer
t o t h e a n t e n n a c o n n e c t o r
through an attenuator.
• Set the Modulation Analyzer as;
HPF
: OFF
LPF : 20 kHz
De-emphasis : OFF
Detector : (P-P)/2
– –
• Connect an Oscilloscope to
the Detect ter minal of the
Modulation Analyzer. – – –
-Adjustment-
NARROW 2 • CH. (16CH/2CH) : CH.9/CH.1
• Transmitting
1) Adjust the waveform using [
←
] / [
→
]
keys on the PC’s keyboard.
2) Push the [ENTER] key to store the
adjust value.
[BAL N]
Square
waveform
MIDDLE* 3 • CH. (16CH/2CH) : CH.9/CH.1
• Transmitting
[BAL Ratio]
WIDE 4 • CH. (16CH/2CH) : CH.10/CH.2
• Transmitting
[BAL Ratio]
CTCSS/DTCS
DEVIATION
-Preparation- 1 <For IC-F24S/F25S/F26S only>
Clone the "ADJ CH ToneMOD.icf" into the transceiver.
• Connect a Modulation Analyzer
t o t h e a n t e n n a c o n n e c t o r
through an attenuator.
• Set the Modulation Analyzer as;
HPF
: OFF
LPF : 20 kHz
De-emphasis : OFF
Detector : (P-P)/2
– –
-Adjustment- 2 • CH. (16CH/2CH) : CH.11/CH.3
• Transmitting
1) Adjust the deviation using [
←
] / [
→
]
keys on the PC’s keyboard.
2) Push the [ENTER] key to store the
adjust value.
[CTCSS/DTCS]
±0.66–0.70
kHz
*: F25/S only
Flat