This service manual describes the latest service information
for the
IC-F3061/62/63/T/S, IC-F3161/62/63/T/S
and
IC-F3163DT/DS
VHF TRANSCEIVER at the time of
publication.
NEVER
connect the transceiver to an AC outlet or to a DC
power supply that uses more than 7.2 V. This will ruin the
transceiver.
DO NOT
expose the transceiver to rain, snow or any liquids.
DO NOT
reverse the polarities of the power supply when
connecting the transceiver.
DO NOT
apply an RF signal of more than 20 dBm (100 mW) to
the antenna connector. This could damage the transceiver’s
front-end.
To upgrade quality, any electrical or mechanical parts and
internal circuits are subject to change without notice or
obligation.
Be sure to include the following four points when ordering
replacement parts:
1. 10-digit Icom parts numbers
2. Component name
3. Equipment model name and unit name
4. Quantity required
<ORDER EXAMPLE>
5030002830 LCD
M4-0078TAY-2
IC-F3061T
Front unit 5 pieces
8810009220 Screw PH B0 M2
×
8 ZK (BT) IC-F3061T
Chassis 10 pieces
Addresses are provided on the inside back cover for your
convenience.
Icom, Icom Inc. and
logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United
Kingdom, Germany, France, Spain, Russia and/or other countries.
ORDERING PARTS
1. Make sure the problem is internal before disassembling
the transceiver.
2.
DO NOT
open the transceiver until the transceiver is
disconnected from its power source.
3.
DO NOT
force any of the variable components. Turn
them slowly and smoothly.
4.
DO NOT
short any circuits or electronic parts. An
insulated tuning tool
MUST
be used for all adjustments.
5.
DO NOT
keep power ON for a long time when the
transceiver is defective.
6.
DO NOT
transmit power into a Standard Signal
Generator or a Sweep Generator.
7.
ALWAYS
connect a 50 dB to 60 dB attenuator between
the transceiver and a Deviation Meter or Spectrum
Analyzer when using such test equipment.
8.
READ
the instructions of test equipment throughly
before connecting a test equipment to the transceiver.
REPAIR NOTES
INTRODUCTION
CAUTION
MODEL
SYMBOL
CHANNEL
SPACING
KEY
PAD
Etc.
IC-F3061T
[USA-01]
15.0/30.0 kHz
10-key
–
IC-F3063T
[GEN-01]
12.5/25.0 kHz
IC-F3062T
[EUR-01]
12.5/20.0/25.0
kHz
IC-F3061S
[USA-01]
15.0/30.0 kHz
4-key
IC-F3063S
[GEN-01]
12.5/25.0 kHz
IC-F3062S
[EUR-01]
12.5/20.0/25.0
kHz
IC-F3062S
[FRG-01]
20.0 kHz
BOS
compatible
IC-F3161T
[USA-01]
15.0/30.0 kHz
10-key
MDC
compatible
IC-F3163T
[EXP-01]
12.5/25.0 kHz
IC-F3162T
[EUR-01]
12.5/20.0/25.0
kHz
IC-F3161S
[USA-01]
15.0/30.0 kHz
4-key
IC-F3163S
[EXP-01]
12.5/25.0 kHz
IC-F3162S
[EUR-01]
12.5/20.0/25.0
kHz
IC-F3161DT
[USA-01]
6.25/15.0/30.0
kHz
10-key
UT-126H
pre-installed
IC-F3161DS
4-key
(IC-F3061T)