![Icom IC-A14IC-A14S Скачать руководство пользователя страница 41](http://html.mh-extra.com/html/icom/ic-a14ic-a14s/ic-a14ic-a14s_instruction-manual_612386041.webp)
36
9
TROUBLESHOOTING
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center.
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
No power comes on.
• The battery is exhausted.
• Recharge the battery pack.
pgs. 29–31
• Bad connection for the battery pack.
• Check the connection to the transceiver.
No sound comes from the
• Squelch level is too deep.
• Set squelch to the threshold point.
speaker.
• Volume level is too low.
• Set [VOL] to a suitable level.
Transmitting impossible.
• WX channels or NAVI band is selected.
• Set COM band in frequency mode.
p. 8
• The battery is exhausted.
• Recharge the battery pack.
pgs. 29–31
Operating frequency or
• Lock function is activated.
• Push and hold [
for 2 sec. to turn the lock p. 9
memory channel can not
function OFF.
be changed.
Scan does not start.
• All memory channels in the selected bank are
• Set the “TAG” settings of desired channels.
p. 20
not programmed as “TAG” channels.
• Squelch is open.
• Set the squelch level to tighten.
p. 9
• There is not more than 2 memorized channels
• Program 2 or more memory channels.
pgs. 13, 14
No beep sounds.
• Beep tones turned OFF.
• Turn the beep tone ON;
IC-A14: Push [FUNC], then push [BEEP](8). p. 22
IC-A14S: Turn the beep tone ON in set mode. pgs. 22, 25
D
CP-22 fuse replacement
If the fuse blows or the receiver stops functioning while oper-
ating with the optional CP-22
cigarette lighter cable
, find
the source of the problem if possible, and replace the dam-
aged fuse with a new rated one (FGB 8 A) as shown right.
aged fuse with a new rated one (FGB 8 A) as shown right.
Fuse 8 A
CONFIDENTIAL!Draft
• Recharge the battery pack.
• Recharge the battery pack.
[
[
CONFIDENTIAL!Draft
]
]
for 2 sec. to turn the lock
for 2 sec. to turn the lock
function OFF.
function OFF.
• Set the “TAG” settings of desired channels.
• Set the “TAG” settings of desired channels.
• Set the squelch level to tighten.
• Set the squelch level to tighten.
• There is not more than 2 memorized channels
• There is not more than 2 memorized channels
• Program 2 or more memory channels.
• Program 2 or more memory channels.
CONFIDENTIAL!Draft
CONFIDENTIAL!Draft
CONFIDENTIAL!Draft
CONFIDENTIAL!Draft
CONFIDENTIAL!Draft
CONFIDENTIAL!Draft
CP-22 fuse replacement
CP-22 fuse replacement
If the fuse blows or the receiver stops functioning while oper-
If the fuse blows or the receiver stops functioning while oper-
ating with the optional CP-22
ating with the optional CP-22
the source of the problem if possible, and replace the dam-
the source of the problem if possible, and replace the dam-
aged fuse with a new rated one (FGB 8 A) as shown right.
aged fuse with a new rated one (FGB 8 A) as shown right.
aged fuse with a new rated one (FGB 8 A) as shown right.
aged fuse with a new rated one (FGB 8 A) as shown right.
only!
only!
pgs. 29–31
pgs. 29–31
p. 7
p. 7
p. 9
p. 9
• Set COM band in frequency mode.
• Set COM band in frequency mode.
for 2 sec. to turn the lock
for 2 sec. to turn the lock
only!
only!
only!
only!
only!
only!
only!
only!