Icom IC-120 Скачать руководство пользователя страница 34

Страница: 34 / 41

SPECIFICATIONS AND OPTIONS

9-2

Specifications

In Canada, Use of 8.33 kHz Channel Spacing of this radio is strictly prohibited and shall not be used.

General

• Frequency range:

IC-A120

118.000 to 136.99166 MHz

IC-A120E (AUS version)

118.000 to 136.97500 MHz

IC-A120E (Others)

118.000 to 136.99166 MHz

• Channel spacing:

25 kHz/8.33*

kHz

• Type of emission:

IC-A120

6K00A3E/5K60A3E (FCC/EXP)

6K00A3E (Industry Canada)

IC-A120E

6K80A3E/5K00A3E*

• Number of memory channels:

200

• Antenna impedance:

(nominal)

• Antenna connector:

SO-239

• Power supply requirement:

13.75 V/27.5 V DC (negative ground)

• Current drain (at 13.75 V):

5.0 A

Maximum audio

4.0 A

• Operating temperature range:

IC-A120

–30˚C to +60˚C,

–22˚F to +140˚F

IC-A120E (AUS version)

–10˚C to +60˚C

IC-A120E (Others)

–20˚C to +55˚C

• Dimensions:

(projections not included)

161 (W)

45 (H)

175 (D) mm,

6.3

(W)

1.8 (H)

6.9 (D) inches

• Weight (approximately):

1.5 kg, 3.3 lb

Except IC-A120E (AUS version).

Transmitter

• Output power:

IC-A120

9 W (Carrier power) typical

10 W (Carrier power) maximum

IC-A120E

9 W±1.5 dB (+15˚C to +35˚C)

9 W+1.5 dB/–3dB (–20˚C to +55˚C)

• Frequency stability:

IC-A120

±5 ppm (–30˚C to +60˚C, –22˚F to +140˚F)

IC-A120E

±1 ppm (0˚C to +40˚C)

• Modulation system:

Last stage modulations

• Audio frequency distortion:

IC-A120

Less than 10% (at 70% modulation)

IC-A120E

Less than 10% (at 85% modu3 dB)

• Spurious emissions:

IC-A120

Less than –60 dBc

IC-A120E*

9 kHz to 30 MHz

Less than –46 dBm

30 MHz to 1 GHz

Less than –36 dBm (For Harmonics)

Less than –46 dBm (For Non-Harmonics)

1 GHz to 4 GHz

Less than –30 dBm (For Harmonics)

Less than –40 dBm (For Non-Harmonics)

Except for operating frequency ±1 MHz.

Содержание IC-120










































Результаты поиска

Содержание IC-120

Отзывы:

Похожие инструкции для IC-120

Бренды по названию

Популярные бренды

Icom IC-120, Полное руководство

Результаты поиска

Содержание IC-120

Отзывы:

Похожие инструкции для IC-120

Бренды по названию

Популярные бренды