manualshive.com logo in svg

Icom I706MKTMG, Инструкция по эксплуатации

Поделиться
Скачать
Icom I706MKTMG Скачать руководство пользователя страница 8

5

1

PANEL DESCRIPTION

■

Rear and side panels

q

GROUND TERMINAL [GND] 

(p. 9)

Connect this terminal to a ground to prevent electri-
cal shocks, TVI, BCI and other problems.

w

ANTENNA CONNECTORS [ANT 1], [ANT 2] 

(p. 11)

Accept a 50 

Ω

antenna with an PL-259 type plug.

• [ANT 1] is for connection to an HF/50 MHz antenna.
• [ANT 2] is for connection to 144 MHz antenna.
• These connectors are switched above or below 60 MHz.

e

DATA JACK [DATA] 

(p. 12)

6-pin min DIN jack to connect a TNC, etc. for pack-
et operation.

r

ACCESSORY SOCKET [ACC] 

(p. 6)

Enables connection to external equipment such as
a TNC for data communications, a linear amplifier or
an automatic antenna selector/tuner, etc.

• See page at right for socket information.

t

RTTY JACK [RTTY] 

(p. 35)

Connects an external terminal unit for RTTY (FSK)
operation.

• The keying polarity and mark/shift frequencies can be

selected in quick set mode (p. 48).

y

CI-V REMOTE CONTROL JACK [REMOTE]

(p. 45)

Designed for use with a personal computer for
remote operation of transceiver functions.

u

MICROPHONE CONNECTOR [MIC] 

(p. 11)

Accepts the supplied microphone (connected in par-
allel with the front panel’s [MIC] connector).

• See pgs. 1 and 2 for microphone notes.
• See p. 8 for microphone connector information.

i

ELECTRONIC KEYER JACK [KEY] 

(p. 33)

Accepts a paddle to activate the internal electronic
keyer.

• Selection between the internal electronic keyer and

straight key operation can be made in quick set mode.
(p. 49)

o

DC POWER SOCKET [DC13.8V] 

(p. 13)

Accepts 13.8 V DC through the supplied DC power
cable.

!0

EXTERNAL SPEAKER JACK [EXT SP] 

(p. 12)

Accepts a 4–16 

Ω

speaker.

!1

TUNER CONTROL SOCKET [TUNER] 

(p. 12)

Accepts the control cable from an optional AH-3 

HF

AUTOMATIC ANTENNA TUNER

.

!2

SPEECH COMPRESSION LEVEL CONTROL
[COMP GAIN] 

(p. 26)

Adjusts the compression level.

• This control is available only when the speech compres-

sor is ON.

COMP

GAIN

/SIDE T

BEEP

DC  1 3 . 8 V

EXT SP

MIC

KEY

TUNER

ANT 1

ANT 2

GND

q

w

e

r

u

i

o

!2 !3

!0

!1

t y

When connecting
a straight key

When connecting
a paddle

(dot)
(com)
(dash)

(

⊕

)

Rear panel view

Recommended
level

Counterclockwise
decreases

Clockwise
increases

COMP

GAIN

/SIDE T

BEEP

Содержание I706MKTMG












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды