IceTech FDHD Series Скачать руководство пользователя | Manualshive

Страница: 36 / 40

background image

SERVICE MANUAL

36

WATER CONDENSER

The water condenser may require cleaning due to scale build-up. The cleaning procedures
require special pumps and cleaning solutions. They must be performed by qualified
maintenance or service personnel.

7.5.- EXTERNAL CLEANING OF THE MACHINE

Clean the area around the ice machine as often as necessary to maintain cleanliness. Sponge

any dust and dirt off the outside of the ice machine with mild soap and water. Wipe dry with a

clean soft cloth. A commercial grade stainless steel cleaner/polish can be used as necessary.

7.6.- WATER LEAKAGE CHECKING

This must be done whenever maintenance is carried out on the machine: check all water
connexions, braces, tubes and hoses in order to eliminate leaks and prevent breakages and
flooding.

«
...
34
35
36
37
38
...
»

Содержание FDHD Series









































Отзывы:

Нет отзывов

Похожие инструкции для FDHD Series

Бренд: Gaggenau Страницы: 7

Бренд: Gaggenau Страницы: 24

Бренд: Gaggenau Страницы: 24

Бренд: Gaggenau Страницы: 6

M39 Dosatron TE

Бренд: La Cimbali Страницы: 50

Бренд: La Cimbali Страницы: 15

Бренд: Saeco Страницы: 68

Бренд: Chefman Страницы: 5

Бренд: Royal Catering Страницы: 21

Бренд: SOLAC Страницы: 36

Бренд: West Bend Страницы: 40

GS-3405T Series

Бренд: Gainscha Страницы: 35

Бренд: Citizen Страницы: 73

Бренд: Cuisinart Страницы: 8

Бренд: Cooks Страницы: 71

Бренд: Newwave Страницы: 19

Nespresso CREATISTA PLUS

Бренд: Sage Страницы: 29

Бренд: Nespresso Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды