background image

10

 

 

Ball

-

gate sensors Operation

 

 

There are two magnetic sensors located under the primary ball gate assembly.  The primary ball gate assembly has a magnetic 

attached underneath so that when the assembly rotates it will pass over one of the two sensors.  When the ball gate assembly 

moves counter clock

-

wise, it will pass over the sensor for the closed position and stop the assembly.  When the ball gate assembly 

rotates clock

-

wise, it will pass over the sensor for the open position and stop the assembly.  Using a volt meter, when the magnet 

passes over either of the sensors, that sensor will have no voltage present.  When the magnet is not over the sensor it should read 

+5 volt of DC power.  With the power off on the game, the sensor is normally open.

 

 

** WARNING ** Never manually move the Primary Ball Gate assembly as damage will occur to the motor gearbox assembly below.

 

 

Ball

-

gate sensors Access

 

 

Remove the two screws that hold the gate cam to the Primary Ball gate assembly.  Slide the Primary Ball gate assembly out.

 

Gate closed Sensor

 

Gate open Sensor

 

Magnetics

 

Gate Cam

 

Primary Ball Gate

 

Primary Ball Gate

 

Sensor

 

Tie

-

Wrap

 

Two pin connector

 

 

Ball

-

gate sensors Removal

 

 

To remove a sensor, disconnect the two pin connector.  Then unscrew the tie

-

wrap and push the sensor out.  To install a replace-

ment sensor, insert the connector from the top through the hole and push firmly down.  Attach the wire harness and re

-

install the 

wire tie.

 

Содержание SNOWBALL TOSS












Отзывы: