Ice RS26L+, Руководство оператора и каталог запасных частей

Страница: 9 / 43

9 ICE RS26L+ / RS32L+
OPERATOR MANUAL
adjusting button (Machine components, #35).
4. Turn on the 1-Step starting button, the Scrub
head assembly and the Squeegee assembly
will lower down automatically, all the presetting
functions will turn on.
5. The machine can scrub in both forward and
backward, press the Directional button (Machine
components, #36) to select the direction.
The horn will sound and the squeegee will
raise automatically (the vacuum motor will turn
off after a short delay) when drive machine
backwards. This is to prevents damaging the
squeegee.
NOTE: Go slow when drive machine
backwards.
6. Press the Propel pedal, the machine start
scrubbing, the speed can be adjusted by
controlling the force of foot stepping, light is
slow, heavy is fast.
NOTE: Go slow on inclines and slippery
surfaces.
7. To stop scrubbing, turn off the 1-Step starting
button, the scrub head will raise automatically,
the squeegee will also raise after a short delay,
please keep moving until the dirty water is
picked up, and then release the propel pedal
and stop scrubbing.
8. Turn off the machine.
BRaKe deVIce
The machine is drived by the Front drive wheel
(Machine components, #11), that is equipped with
a brake device. When you release the Propel
pedal, the machine will stop travel, the park brake
will engage after a short delay.
The machine is equipped with a Brake pedal
(Machine components, #9), that can be used to
control the machine if quicker stopping is needed
or if operating on an incline.
emeRGency Stop Button
The machine is equipped with an Emergency stop
button (Machine components, #17), please push
it if any emergency, that will shut off all power of
machine and brake immediately.
To restart the machine, please reset the
Emergency stop button, and turn off the machine
and then restart.
NOTE: Please hold the steering wheel when
emergency stop.
WaRnInG: fire or explosion Hazard. do
Not Pick Up Flammable Materials Or Reactive
metals.
1. Go slow on inclines and slippery surfaces, go
slow when turn and reverse. Do not operate the
machine on inclines that exceed 7% (4°).
2. Drive machine in a straight path as possible,
avoid turning the Steering wheel too sharply
when machine is in motion. avoid sudden turns
except emergencies.
3. Do not keep the machine in the same position
with pad / brush spinning, keep the machine
moving to prevent damage to floor finish.
4. If the squeegee assembly leaves streaks on the
floor, raise the squeegee off the floor and wipe
the blades down with a damp cloth. Pre-sweep
the area to prevent leaving streaks on the floor.
5. To obtain the optimum cleaning performance,
you can adjust the brush pressure, solution
flow and detergent dosage as your required. If
poor picking up water performance is observed,
please stop scrubbing and check the squeegee
blade, adjust or replace if necessary.
6. If the dirty water path exceed the width of
squeegee, please adjust the side squeegee
assembly.
7. Pour a recommended defoamer into the
recovery tank if excessive foam appears.
WaRnInG: the foam do not activate
water level switch, excessive foam may result
in vacuum motor damage.
8. Press the Horn button (Machine components,
#27) to alert if necessary.
9. The machine is equipped with a Warning light
(Machine components, #21), you can select turn
ON or OFF by the Warning light button (Machine
components, #40).
10. If there have Fault icon display and blinking
on the touch screen, please stop using the
machine and to eliminate the fault (Please see
FAULT CODES AND ELIMINATE section).
11. For heavily soiled areas, please use HEAVY
DUTY SCRUBBING mode by work mode select
button.
12. If you only want to pick up water needn't
scrubbing, Turn on the Vacuum motor
button(Machine components, #38) , the
squeegee will lower down, and turn off the
1-Step starting button (if it is ON), the scrub
head will raise and then start to picking water
up.
WHIle opeRatInG macHIne