Ice i28BTL, Руководство оператора и каталог запасных частей

Страница: 8 / 39

8 ICE i28BTL / i32BTL
OPERATOR MANUAL
fIllInG tHe SolutIon tanK
The machine is equipped with a hose fill-port
(Machine components, item #7) at the rear of
the machine, and a bucket fill-port (Machine
components, item #26)located under the recovery
tank. Before accessing the bucket fill-port make
sure that the recovery tank is empty.
Fill the solution tank to the "100L" level on the
solution tank sight gauge. When using the bucket
fill-port, stop filling when the level reaches the
bottom edge of the fill-port.
NOTE: When filling the solution tank with a
bucket, make sure that the bucket is clean. Do not
use the same bucket for filling and draining the
machine.
WARNING: Do not put any flammable
materials into solution tank. this can cause an
explosion or a fire. Only use recommended
cleaning chemicals. contact your janitorial
supply distributor for recommendations on
proper chemicals.
WaRnInG: do not operate machine
unless you have read and understand this
manual.
1. Swipping the ID card (Machine components,
item #18) to turn on the machine.
2. Check the LED display screen (Panel
components, item #4), if there are fault condes
(Panel components, item #18) and the Fault
indicator (Panel components, item #1) in blink,
please DO NOT operate the machine unless the
faults have been eliminated (please see FAULT
CODES AND ELIMINATE section).
3. Turn on the 1-Step scrub head up/down
button, the scrub head will be lowered down
automatically.
4. Lower squeegee assembly to the floor by
lowering the Squeegee lift lever.
5. Check the solution flow indicator (Panel
components, item #9), press the Solution flow
adjusting button (Panel components, item #10)
to get a desired solution flow.
NOTE: Solution will not begin to flow until the
control handle bail is pulled.
6. Turn on the Vacuum motor switch(Panel
components, item #8).
7. Pull the Control handle bail (machine
components, item #17) backwards to start
scrubbing .The machine will automatically
propel forward. To reverse the machine, simply
push the control handle bail forward.
NOTE:
Raise squeegee when reversing machine.
8. The scrubbing speed can be adjusted, press
the Speed increase/ decrease button (Panel
components, item #14, #16) to a desired speed.
NOTE: 45-60 meters (150-200 ft)per minute is
the recommended scrubbing speed.
9. The brush pressure can be adjusted, press the
Brush pressure increase/ decrease button
(Panel components, item #3,#6) to get a
desired brush pressure.
10. To stop scrubbing, release the control handle
bail, turn off the 1-Step scrub head up/down
button to raise he scrub head assembly, raise
the squeegee assembly.
WaRnInG: fire or explosion Hazard. do
not pick up flammable materials or Reactive
metals.
1. Go slow on inclines and slippery surfaces. Do
not operate the machine on inclines that exceed
5% (3°).
2. Do not keep the machine in the same position
with pad / brush spinning, keep the machine
moving to prevent damage to floor finish.
3. If the squeegee assembly leaves streaks on the
floor, raise the squeegee off the floor and wipe
the blades down with a damp cloth. Pre-sweep
the area to prevent leaving streaks on the floor.
4. Pour a recommended defoamer into the
recovery tank if excessive foam appears.
WaRnInG: do not allow foam to enter
the float shut-off screen, vacuum motor
damage will result. foam will not activate the
float shut-off screen.
5. Occasionally check the battery meter(Panel
components, item #2). when the battery is very
low, stop scrubbing and recharge the batteries.
WaRnInG: When battery meter is in the
red, do not continue to operate the machine.
Battery damage may result.
macHIne opeRatIon
WHIle opeRatInG macHIne