manualshive.com logo in svg

Ice-O-Matic Pearl Ice GEM0650R' Pearl Ice GEM0655A, Руководство по обслуживанию и установке

Поделиться
Скачать
Ice-O-Matic Pearl Ice GEM0650R' Pearl Ice GEM0655A Скачать руководство пользователя страница 3

GEM0650/0956/1256 Remote 

 

Introduction 

Page i 

 

How To Use This Manual 
 
Ice-O-Matic provides this manual as an aid to the end user and service technician in installation and 
maintenance of the 

Pearl Ice™ Series 

ice machines.  Do not attempt to perform installation, start-up or 

maintenance unless you have read and fully understand this manual. 
 
If, at any time, you encounter conditions that are not addressed in this manual, call, E-mail or write the  
Ice-O-Matic Service Department:  
 
Ice-O-Matic  

 

11100 E. 45

th

 Ave. 

Denver, Co. 80239 
Attn: Technical Service Department 
E-Mail: [email protected]  
 
Telephone Numbers   

 

 

Any Service communication must include: 

800-423-3367 All 

Departments   

 

•

 Model Number 

888-349-4423      Technical Assistance Only  

•

 Serial number 

303-371-3737 

     

•

 A detailed explanation of the problem 

 

Keep this manual for future reference. 
 

The GEM0650R, GEM0956R and GEM1256R Service Parts Manuals are available separately. 

 
Ice-O-Matic icemakers and dispensers are not approved for outdoor installation. 
 
WARNING:  Always disconnect electrical power and shut off water supply whenever maintenance or 
repairs are performed on the ice machine and related equipment. 
 
CAUTION:  Always wear protective eyewear whenever maintenance or repairs are performed on the ice 
machine and related equipment 

 

Содержание Pearl Ice GEM0650R' Pearl Ice GEM0655A



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды