Ice-O-Matic EF Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 72

background image

Flake Ice Machines

General Information

Page

A6

Installation Guidelines

Note: Installation should be performed by an ICE-O-Matic trained Service Technician.
For proper operation of the ICE-O-Matic ice machine, the following installation guidelines
must be followed. Failure to do so may result in loss of production capacity, premature part
failures, and may void all warranties.

Ambient Operating Temperatures

Minimum Operating Temperature: 50°F (10°C)
Maximum Operating Temperature 100°F (38°C), 110°F (43°C) on 50 Hz. Models.

Note: ICE-O-Matic products are not designed for walk in cooler applications or outdoor
installation.

Incoming Water Supply

(See Plumbing Diagram for line sizing Page A7-A9)

Minimum incoming water temperature: 40°F (4.5°C)
Maximum incoming water temperature: 100°F (38°C)
Minimum incoming water pressure: 20 psi (1.4 bar)
Maximum incoming water pressure: 60 psi (4.1 bar)

Note: If water pressure exceeds 60 psi (4.1 bar), a water pressure regulator must be
installed.

Drains:

Route bin drain, float drain and water condenser drain individually to a floor drain

.

The use of condensate pumps for draining water is not recommended by ICE-O-Matic.
ICE-O-Matic assumes no responsibility for improperly installed equipment.

Water Filtration

A water filter system should be installed with the ice machine.

Clearance Requirements

Self contained air cooled ice machines must have a minimum of 6 inches (15cm) of clearance
around the entire machine.

Stacking

EF and EMF Series ice machines are not designed to be stacked.

Dispenser Application

EF and EMF Series ice machines are not designed to be placed on dispensers.

Electrical Specifications

The machine must be installed on a separate circuit.
Refer to the serial plate at the rear of the ice machine or the charts on Page A5.

Adjustments

Level the machine.
Check the primary and secondary bin control for proper adjustment, Page G3.
Check the safety control for proper adjustment, Page G3.
Check the water in the water float for proper level, Page D1.
Check the water regulating valve adjustment if water cooled, Page F6.

«
...
6
7
8
9
10
...
»

Содержание EF Series









































































Отзывы:

Нет отзывов

Похожие инструкции для EF Series

Бренд: MAGIMIX Страницы: 46

Бренд: IceTech Страницы: 28

Бренд: La Pavoni Страницы: 16

Бренд: Russell Hobbs Страницы: 8

Бренд: Senya Страницы: 51

Бренд: tomado Страницы: 20

300 Pizzelle Chef

Бренд: vitantonio Страницы: 2

Бренд: Russell Hobbs Страницы: 8

Бренд: DeLonghi Страницы: 18

Бренд: Cascade Страницы: 4

ENFINIGY 53103-3

Бренд: Zwilling Страницы: 136

Бренд: M&V S.r.l. Страницы: 14

Бренд: Citizen Страницы: 73

MAGNIFICA EVO FEB292X

Бренд: DeLonghi Страницы: 28

DeLonghi PICCOLO XS

Бренд: Nescafe Dolce Gusto Страницы: 21

Бренд: Faema Страницы: 148

Бренд: POSline Страницы: 3

Бренд: Ice-O-Matic Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды