background image

Maintenance    13 

 

 

Maintenance 

 

In  order  to  maintain  the  image  quality  and  proper  functioning  of  the  device,  please  read  the 

following maintenance instructions carefully and hold rigid adherence. 

Disassembly and Desiccant Replacement 

 

Carefully follow the instructions in the manual when performing any disassembly operation 

about  the  device;  otherwise,  it  might  cause  water  leakage  or  poor  image  quality  due  to 

unprofessional disassemble.   

 

Please contact after-sale service for desiccant replacement if there is condensed fog found 

on the lens after unpacking or when the desiccant turns green. (Not all models are included 

with the desiccant). 

Maintaining Lens and Mirror Surface 

 

The  lens  and  mirror  surface  are  covered  with  antireflection  coating,  which  could  be 

contaminated or damaged and result in lens scratches or haze image when being touched 

with dust, grease, fingerprints and other similar substances. 

 

Do not touch the image sensor directly (CCD or CMOS). Dust and dirt could be removed 

with air blower, or you can wipe the lens gently with soft cloth that moistened with alcohol. 

Maintaining Device Body 

 

Device  body  can  be  cleaned  with  soft  dry  cloth,  which  can  also  be  used  to  remove 

stubborn stains when moistened with mild detergent.   

 

To  avoid  possible  damage  on  device  body  coating  which  could  cause  performance 

decrease, do not use volatile solvent such as alcohol, benzene, diluent and so on to clean 

the device body, nor can strong, abrasive detergent be used. 

Содержание AVS-4KD8021-IR




















Отзывы: