background image

Caution Notices

CAUTION:
This unit may have two linecords. To remove all power,
disconnect both linecords.

CAUTION:
This unit weighs 38.5 kg.

CAUTION:
Do not remove cover, do not service, no serviceable parts.

CAUTION:
Double pole/neutral fusing

CAUTION:
A

Standby

condition is indicated by the symbol to the right of

DC

directly above the switch, SW1. When SW1 is toggled to the

right position directly under the

Standby

symbol, the unit’s

AC-power is not shut off.

CAUTION:
The stabilizer must be correctly attached to the bottom front of
the rack to prevent the rack from tipping forward while the 2104
Model DU3 is being removed from the rack.
Do not pull out or install any unit if a stabilizer is not attached to
the rack.

CAUTION:
The stabilizer must be correctly attached to the bottom front of
the rack to prevent the rack from tipping forward while the 2104
Model DU3 is being installed into the rack.
Do not remove or install any unit if a stabilizer is not attached to
the rack.

CAUTION:
A 2104 Model DU3 weighs up to 38.5 kg (85 lb) with the
maximum number of disk drive modules installed. Do not
attempt to lift the 2104 into the rack unless all the disk drive
modules have been removed.

CAUTION:
A 2104 Model DU3 weighs up to 38.5 kg (85 lb) with the
maximum number of disk drive modules installed. Do not
attempt to remove the 2104 from the rack unless all the disk drive
modules have been removed.

CAUTION:
Do not attempt to lift the 2104 by yourself. Ask another person
for aid.

CAUTION:
Do not insert hands or tools into the empty space that contained
the fan assembly.

82

2104 Models DU3 and TU3 Operator’s Guide

Содержание TU3 2104







































































































































Отзывы: