IBM TS2280 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 142

background image

Troubleshooting

If you encounter problems when running the drive, refer to the flowchart in Figure 26. For explanations
of codes on the Single-character Display (SCD), see “Single-character display (SCD)” on page 13. Review
the “Pre-call checklist” on page 62 before calling IBM Technical Support.

Procedure 1: Determining firmware level and capturing drive dump

Customers are responsible for updating Firmware. For optimum performance, the customer must obtain
the current level of firmware for the unit by downloading the firmware from http://www.ibm.com/
support/fixcentral.

Yes

Yes

1. Try another electrical outlet.
2. Try another power cord.
3. Refer to the pre-call checklist in this chapter before calling

IBM Technical Support.

4. Contact IBM Technical Support.

Ensure that the SAS communication path
between the host and the drive is functioning properly
(refer to Procedures 3 and 4 in this chapter).

Refer to the pre-call checklist in this chapter before calling
IBM Technical Support. Contact IBM Technical Support.

1. Refer to the section about codes on the single-character

display in this guide.

2. Ensure that the latest level of firmware is installed on the

drive (refer to Procedure 1 in this chapter).

3. Refer to the pre-call checklist in this chapter before calling

IBM Technical Support.

4. Contact IBM Technical Support.

Refer to Procedure 2 in this chapter.

No

No

No

Yes

No

No

Yes

Yes

a80hh083

Start

Does the

Tape Drive

power on?

Does air flow

from the fan?

Does the

SCD and fault

light indicate

an error?

Does the tape

cartridge load and

unload properly?

1. If you are still having

problems running the Tape
Drive refer to the pre-call
checklist in this chapter
before calling IBM Technical
Support.

2. Contact IBM Technical

Support.

Does the

Tape Drive

communicate

with the server?

correctly

Figure 26. Flowchart for Analyzing Maintenance Problems

© Copyright IBM Corp. 2017

59

«
...
79
80
81
82
83
...
»

Содержание TS2280















































































































































Отзывы:

Нет отзывов

Похожие инструкции для TS2280

Mobile Ultra Memory Stick Micro

Бренд: SanDisk Страницы: 1

Бренд: Hamlet Страницы: 10

Biometric Hard Drive

Бренд: LaCie Страницы: 44

Бренд: Campbell Страницы: 30

Бренд: Seagate Страницы: 40

Бренд: NCR Страницы: 10

Бренд: G-Technology Страницы: 33

5BIG THUNDERBOLT 2

Бренд: LaCie Страницы: 20

Бренд: Panasonic Страницы: 33

Бренд: Panasonic Страницы: 48

Бренд: Infrant Technologies Страницы: 98

Бренд: Lakeshore Страницы: 7

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 4

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 43

Бренд: Samsung Страницы: 60

Бренд: Toshiba Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды