IBM TS2280 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 142

IBM TS2280 Скачать руководство пользователя страница 59

Ultrium media

IBM Ultrium media is available in the following types:

v

Data cartridge

v

WORM (Write Once, Read Many) cartridge

v

Cleaning cartridge

To ensure that your IBM Ultrium tape drive conforms to IBM's specifications for reliability, use only IBM
LTO Ultrium tape cartridges. You can use other LTO-certified data cartridges, but they might not meet
the standards of reliability that are established by IBM. The IBM LTO Ultrium data cartridge cannot be
interchanged with the media used in other IBM non-LTO Ultrium tape products.

Figure 11 shows the IBM LTO Ultrium data cartridge and its components.

▌1▐

LTO cartridge memory

▌4▐

Write-protect Switch

▌2▐

Cartridge door

▌5▐

Label area

▌3▐

Leader Pin

▌6▐

Insertion guide

Data cartridges

The different generations of IBM Ultrium data cartridges are identified by color:

Table 7. Cartridge types and colors

Type

Color

Ultrium 8

Burgundy

Ultrium 8 WORM

Burgundy and Silvery gray

Ultrium 7

Purple

Ultrium 7 WORM

Purple and Silvery gray

Ultrium 6

Black

Ultrium 6 WORM

Black and Silvery gray

Figure 11. The IBM LTO Ultrium data cartridge

© Copyright IBM Corp. 2017

37

«
...
57
58
59
60
61
...
»

Содержание TS2280















































































































































Отзывы:

Нет отзывов