background image

Note:

All vertical rack measurements are given in rack units (U). One U is equal to 4.45 cm (1.75 in.).

The U levels are marked on labels on one front mounting rail and one rear mounting rail.

2.

With the sides and back of the shelf facing up, carefully lift the shelf into the rack between the front
and back rack rails with the shelf flanges behind the front rack rails.

3.

Align the holes in the shelf flange exactly with the holes in the front rack rails.

4.

Holding the shelf 

▌1▐

level, insert a screw through the top hole 

▌3▐

in each front flange of the shelf.

Loosely thread the screws into the front mounting rails.

5.

Check that the shelf is at the same level on the four mounting rails.

6.

Insert a screw through the bottom hole 

▌4▐

in each front flange of the shelf. Loosely thread the screws

into the front mounting rails.

7.

Tighten all mounting screws with a 7 mm nut driver or a 7 mm socket wrench.

8.

Route cables down one of the rear rack rails by threading each tie wrap (see 

▌5▐

in Figure 30) through

a hole in the rail and around the cables. One tie wrap must be located near the rear of the 3580; the
other must be located farther down the rack rail. Tighten cable ties securely around the cables so the
cables cannot be pulled out. Cut off tie wrap excess.

The shelf installation is complete. You can now install your equipment on the shelf.

Removing the shelf from the rack

To remove the shelf from the rack, reverse the steps in the installation procedure.

1

4

3

4

a80hh004

3

2

Figure 29. Front view of shelf attached to rack rails

5

a67ru013

Figure 30. Rear view of shelf with cables attached to rack rails with tie wraps

Appendix D. Installing a 19-inch rack mount kit (optional)

81

Содержание TS2280















































































































































Отзывы: