manualshive.com logo in svg

IBM TS22 Series, Руководство пользователя

Поделиться
Скачать
IBM TS22 Series Скачать руководство пользователя страница 24

The web page format is changed to text mode by selecting the “Text Only version” box near the top of the web page. In text mode, the tape drive status information
can be copied and pasted easily if it must be sent to support personnel.

Diagnostic and maintenance functions

Refer to this section for information on diagnosing and maintaining your tape drives.

The drive can:

Run diagnostics
Test write and read functions
Test a suspect tape cartridge
Update firmware
Complete other diagnostic and maintenance functions

The drive must be in Maintenance mode to complete these functions.
Attention: Maintenance functions cannot be run concurrently with read or write operations. While in maintenance mode, the tape drive does not accept host
interface commands from the server. The tape drive does accept LDI or RS-422 commands.

Table 1

 describes each diagnostic and maintenance function that the drive can complete, gives the function code that appears on the Single-character Display

(SCD), and directs you to the instructions for completing the function. Use a customer-supplied scratch (blank) data cartridge for diagnostic testing. The diagnostic
and maintenance functions are not supported on the WORM and partitioned data tape cartridges.

Table 1. Diagnostic and maintenance functions

Function Code

Diagnostic or Maintenance Function

Instructions Location

Exit Maintenance Mode: Causes the drive to become available for reading and writing data.

Function code 0:
Maintenance mode

Run Drive Diagnostics: Runs tests to determine whether the drive can properly load and unload cartridges, and read
and write data.

Function code 1: Run
drive diagnostics

Update Tape Drive Firmware from FMR Tape: Loads updated firmware from a field microcode replacement (FMR)
tape.

Function code 2:
Update drive firmware
from FMR tape

Create FMR Tape: Copies its field microcode replacement (FMR) data to a customer-supplied scratch (blank) data
cartridge.

Function code 3: Create
FMR tape

Force a Drive Dump: Completes a memory dump of data (also known as saving a microcode trace).

Function code 4: Force
a drive dump

Copy Drive Dump: Copies data from a drive memory dump (captured by using Function Code 4) to the beginning of a
customer-supplied scratch (blank) data cartridge, copies a drive memory dump to flash memory, or erases a memory
dump from flash memory.

Function code 5: Copy
drive dump

Run Host Interface Wrap Test: Checks the circuitry from and to the connector.

Function code 6: Run
host interface wrap test

Run RS-422 Wrap Test: This test causes the drive to run a check of the circuitry and connector for the RS-422
interface.

Function code 7: Run
RS-422 wrap test

Unmake FMR Tape: Erases the FMR data on a customer-supplied scratch (blank) data cartridge and rewrite the
cartridge memory on the tape. This action turns the cartridge into a valid customer-supplied scratch data cartridge.

Function code 8:
Unmake FMR tape

IBM TS22xx Tape Drives 

17

Содержание TS22 Series
































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды