IBM System x iDataPlex dx360 M4 7912 страница 308 Скачать руководство пользователя | Manualshive

Страница: 308 / 400

background image

Installing the 2U chassis fan assembly

To install the 2U chassis fan assembly, complete the following steps.

Fan assembly

1. Touch the static-protective package that contains the fan assembly to any

unpainted

metal surface on the outside of the chassis; then, remove the fan

assembly from the package.

2. Orient the fan assembly over the opening in the chassis. Make sure that the

power connector on the fan assembly aligns with the connector on the power
supply.

3. Lower the fan assembly into the chassis and press down on the tab above the

power connector to make sure that it is fully seated.

4. Install the top cover (see “Installing the 2U chassis fan-assembly top cover” on

5. Install any system-board trays that you removed (see “Installing the

system-board tray in a 2U chassis” on page 279).

6. Install the chassis in the iDataPlex rack, (see “Installing the 2U chassis in a

rack” on page 285).

Removing the system battery

The following notes describe information that you must consider when replacing the
battery:

v

IBM has designed this product with your safety in mind. The lithium battery must
be handled correctly to avoid possible danger. If you replace the battery, you
must adhere to the following instructions.

Note:

In the U. S., call 1-800-IBM-4333 for information about battery disposal.

v

If you replace the original lithium battery with a heavy-metal battery or a battery
with heavy-metal components, be aware of the following environmental
consideration. Batteries and accumulators that contain heavy metals must not be

290

System x iDataPlex dx360 M4 Types 7912 and 7913: Problem Determination and Service Guide

«
...
306
307
308
309
310
...
»

Содержание System x iDataPlex dx360 M4 7912

















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x iDataPlex dx360 M4 7912

Бренд: Xena Networks Страницы: 6

Бренд: LG Страницы: 24

Бренд: Seventh Circle Audio Страницы: 8

Бренд: Brocade Communications Systems Страницы: 182

Бренд: OSS Страницы: 59

Бренд: Turin Networks Страницы: 36

iConverter 8090-0

Бренд: OST Страницы: 12

Бренд: TYAN Страницы: 74

Бренд: Spirent communications Страницы: 6

Бренд: Supero Страницы: 188

Бренд: Apcon Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды