IBM System x iDataPlex dx360 M4 7912 Скачать руководство пользователя страница 303

Страница: 303 / 400

Installing the 2U chassis in a rack

To install the 2U chassis in a rack, complete the following steps.

1. If you are installing a new chassis, install the power supply cage and fan

assembly that you removed from the old chassis (see “Installing a power supply
in a 2U chassis” on page 317 and “Installing the 2U chassis fan assembly” on
page 290).

2. If you have the iDataPlex rack:

a. Fasten the captive screw affiliated to the left flange of the chassis to the

rack.

b. On the right side of the chassis, mount the chassis with one M6 screw

which is included in the iDataPlex rack rail kit.

3. If you have the Enterprise rack:

a. Remove the two removable brackets on both sides of the chassis in

advance.

The following illustrations show the locations of the brackets and the screws
on the chassis.

Bracket on the left hand side

Bracket on the right hand side

2U chassis

Screw

Bracket

2U chassis

Screw

Bracket

b. Mount the chassis to rack with two M6 screws which are included in the

Enterprise rack rail kit.

Chapter 5. Removing and replacing server components

285

Содержание System x iDataPlex dx360 M4 7912

















































































































































































































































































































































































































Результаты поиска

Содержание System x iDataPlex dx360 M4 7912

Отзывы:

Бренды по названию

Популярные бренды

IBM System x iDataPlex dx360 M4 7912, Руководство по обслуживанию

Результаты поиска

Содержание System x iDataPlex dx360 M4 7912

Отзывы:

Бренды по названию

Популярные бренды