manualshive.com logo in svg

IBM SurePOS 700 Series, Руководство по обслуживанию оборудования

Поделиться
Скачать
IBM SurePOS 700 Series Скачать руководство пользователя страница 68

To replace the main riser card battery:

1. Insert one edge of the battery (positive side UP) under the battery socket's

longer tabs (

B

in Figure 36, toward the front of the riser card).

2. Push down on the opposite edge of the battery to snap it under the short tabs.

3. To reinstall the spline, reverse the steps in “Replacing the spline” on page 46.

Replacing the DASD cage

To remove the direct access storage device (DASD) cage:

1. Follow the steps in “Replacing a hard disk drive” on page 38 and in “Replacing

the optical drive” on page 39 to remove all drives from the drive bay.

Note:

Step 1 is only necessary if you are actually replacing just the DASD
cage; if you are merely removing it as part of another procedure, ignore
this step.

2. Follow the steps in “Replacing the spline” on page 46 to remove the spline from

the system.

3. While holding the DASD cage, push down on the cage lock tab (

B

) with your

thumb and pull up.

Figure 36. Removing the riser battery

50

SurePOS 700-723/743/783/784 Hardware Service Guide

Содержание SurePOS 700 Series





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды