manualshive.com logo in svg

IBM SurePOS 700 Series, Руководство по обслуживанию оборудования

Поделиться
Скачать
IBM SurePOS 700 Series Скачать руководство пользователя страница 28

USB support

The base subsystem is implemented on the main processor board and uses the
core USB support that is provided by the system-board chip set. SurePOS 700
Models 723, E23, 743, C43, E43, 783, E83, 784, C84, and E84 support the USB
1.1. and 2.0 standard. All system board USB controllers are Universal Host
Controller Interface (UHCI) and Enhanced Host Controller Interface (EHCI)
compliant.

Unique software interface

For the software programmer, the SurePOS 700 appears as a PCI-based PC
system unit with the usual PC peripherals. The unique POS function is packaged on
the PCI riser card. The system unit also provides the following unique functions:

v

128 KB of nonvolatile random access memory (NVRAM)

v

A ROM bank that connects to the system ROM during power-on self-test (POST)
to provide additional functionality and information

v

An interface to the RS-485 (Electronic Industries Alliance [EIA] 485) subsystem, if
the system is equipped with RS-485 ports

1

v

An interface to the POS USB subsystem

1

v

An interface to the POS RS-232 subsystem

1

Physical characteristics

This section gives you the physical characteristics for the SurePOS 700 Series
Models 723, E23, 743, C43, E43, 783, E83, 784, C84, and E84 for narrow, wide,
and wide with uninterruptible power supply models.

Dimensions

Table 4 lists the dimensions for the wide and narrow models.

Table 4. Wide and narrow model dimensions

Footprint

Width

Depth

Height

Weight

Wide

435 mm
(17.13 in.)

475 mm
(18.70 in.)

117.3 mm
(4.62 in.)

11.8 kg
(30.64 lbs)

Narrow

320 mm
(12.60 in.)

475 mm
(18.70 in.)

117.3 mm
(4.62 in.)

11.4 kg
(25.13 lbs)

Wide with
uninterruptible
power supply

435 mm
(17.13 in.)

475 mm
(18.70 in.)

117.3 mm
(4.62 in.)

18.4 kg
(40.57 lbs)

Controls and indicators

Figure 5 on page 11 describes the front panel controls and indicators.

1. IBM drivers and operating systems isolate these changes from the application.

10

SurePOS 700-723/743/783/784 Hardware Service Guide

Содержание SurePOS 700 Series





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды