1.
From
the
SCSISelect
Utility
main
menu,
select
Configure/View
HostRAID
Settings
.
2.
From
the
list
of
ready
drives,
type
C
to
create
an
array.
3.
Select
RAID-1
when
asked
to
select
the
RAID
type.
4.
From
the
list
of
ready
drives,
select
the
two
drives
that
you
want
to
group
into
the
array.
5.
Select
Create
new
RAID-1
.
6.
Type
an
identifier
for
the
array.
7.
Select
Yes
to
create
the
array.
8.
Press
Esc
to
exit
the
utility.
9.
Restart
the
server.
Viewing
the
configuration
You
can
use
the
SCSISelect
Utility
program
to
view
information
about
the
SCSI
controller.
From
the
list
of
available
arrays,
select
an
array
and
press
Enter.
Press
Esc
to
exit
the
utility.
Using
the
Boot
Menu
program
The
Boot
Menu
program
is
a
built-in,
menu-driven
configuration
utility
program
that
you
can
use
to
temporarily
redefine
the
first
startup
device
without
changing
settings
in
the
Configuration/Setup
Utility
program.
Complete
the
following
steps
to
use
the
Boot
Menu
program:
1.
Turn
off
the
server.
2.
Restart
the
server.
3.
Press
F12.
4.
Select
the
startup
device.
The
server
returns
to
the
startup
sequence
that
is
set
in
the
Configuration/Setup
Utility
program
the
next
time
the
server
starts
or
after
the
temporary
settings
expire.
Configuring
the
Ethernet
controllers
The
Ethernet
controllers
are
integrated
on
the
system
board.
They
provide
an
interface
for
connecting
to
a
10-Mbps,
100-Mbps,
or
1-Gbps
network
and
provide
full-duplex
(FDX)
capability,
which
enables
simultaneous
transmission
and
reception
of
data
on
the
network.
If
the
Ethernet
ports
in
the
server
support
auto-negotiation,
the
controllers
detect
the
data-transfer
rate
(10BASE-T,
100BASE-TX,
or
1000BASE-T)
and
duplex
mode
(full-duplex
or
half-duplex)
of
the
network
and
automatically
operate
at
that
rate
and
mode.
You
do
not
have
to
set
any
jumpers
or
configure
the
controllers.
However,
you
must
install
a
device
driver
to
enable
the
operating
system
to
address
the
controllers.
For
device
drivers
and
information
about
configuring
the
Ethernet
controllers,
see
the
Broadcom
NetXtreme
Gigabit
Ethernet
Software
CD
that
comes
with
the
server.
For
updated
information
about
configuring
the
controllers,
go
to
http://www.ibm.com/pc/support/.
Chapter
2.
Configuring
the
server
21
Содержание SC25-R345-20
