IBM POWERPC 970MP Скачать руководство пользователя страница 22

Страница: 22 / 25

Application Note

(Includes Differences for 970FX to 970MP)
IBM PowerPC

970MP RISC Microprocessor

Preliminary

8. Package

Page 22 of 25

AppNote_970FX-MP_Differences_Body.fm.1.0

November 15, 2006

8.3 PowerPC 970MP Microprocessor Package Dimensions

IBM offers the 970MP in a ceramic ball grid array, CBGA, package which supports 575 balls. The 970MP is
offered in a lead reduced package with SnAgCu (SAC) balls. The following figures contain views of the
970MP package.

Figure 8-1

shows the side and top views of the Pb-reduced package including the height from the top of the

die to the bottom of the solder balls.

Figure 8-2

shows a bottom view of the PowerPC 970MP package.

Table 8-4. Deleted 970FX Pins - not found on 970MP

970FX Pin

970FX Function

PROCID2

Least significant bit in the 3 bit processor ID, automatically set on PowerPC 970MP

THERM_INT_B

Dedicated thermal interrupt signal, removed due to lack of use

TRIGGERIN

Initiate trace collection from outside, removed due to lack of use

PSYNC_OUT

Used to check phase alignment while debugging, removed due to lack of use

SPARE_GND

Unneeded Spare

Содержание POWERPC 970MP


























Результаты поиска

Содержание POWERPC 970MP

Отзывы:

Похожие инструкции для POWERPC 970MP

Бренды по названию

Популярные бренды

IBM POWERPC 970MP, Примечание к применению

Результаты поиска

Содержание POWERPC 970MP

Отзывы:

Похожие инструкции для POWERPC 970MP

Бренды по названию

Популярные бренды