IBM Power Systems Series Скачать руководство пользователя страница 63

Страница: 63 / 134

Table 10. Sensor information, event description, and service action for the 5104-22C, 9006-12P,

9006-22C, or 9006-22P (continued)
Sensor name (Sensor ID)

Event description

Service action

Watchdog (0xFF)

• Timer Expired
• Reserved1
• Reserved2
• Reserved3
• Reserved4

No service action is required.

• Hard Reset
• Power Down
• Power Cycle
• Timer Interrupt

Search for serviceable SEL events

that have a time stamp close to

the time stamp of this SEL event.

If you found a serviceable SEL

event, perform the service action

that is indicated in this table for

the SEL event. If you cannot boot

the system to the Petitboot

menu, go to “Resolving a system

firmware boot failure” on page 5.

Isolation procedures

Use this information to isolate problems that might occur with your system.

EPUB_PRC_FIND_DECONFIGURE_PART isolation procedure

A part vital to the system has been deconfigured.

Procedure

1. Use the

ipmitool

command to examine system event logs (SELs).

• To list SELs by using an in-band network, use the following command:

ipmitool sel elist

• To list SELs remotely over the LAN, use the following command:

ipmitool -I lanplus -U <username> -P <password> -H <BMC IP addres or BMC hostname> sel

elist

2. Identify all SELs with the value

OEM record df

and Correctable Machine Check Error or Transition

to Non-recoverable in the description. Did you find one or more SELs with the value

OEM record df

and Correctable Machine Check Error or Transition to Non-recoverable in the description?

Then

Yes:

Continue with the next step.

No:

Go to “Contacting IBM service and support” on page 61. This ends the procedure.

3. For each of the SELs that you identified in step “2” on page 49, determine the sensor name that is

associated with each SEL. Replace the following items, one at a time until the problem is resolved:
Note:
• If your system is a 5104-22C or 9006-22C, go to “5104-22C or 9006-22C locations” on page 63 to

identify the physical location and removal and replacement procedure.

Beginning troubleshooting and problem analysis 49

Содержание Power Systems Series







































































































































Результаты поиска

Содержание Power Systems Series

Отзывы:

Бренды по названию

Популярные бренды

IBM Power Systems Series, Анализ проблем, составные части системы и расположение

Результаты поиска

Содержание Power Systems Series

Отзывы:

Бренды по названию

Популярные бренды