IBM Power System 5148-22L Скачать руководство пользователя

Страница: 104 / 204

Type

iprconfig

on the command line of the Linux session and press

Enter

. The IBM Power RAID

Configuration Utility display is shown.

Select Analyze log. Press

Enter

. The Kernel Messages Log display is shown.

Select View most recent ipr error messages from the Kernel Messages Log display. Press

Enter

Find the entry in the log for the drive you want to replace.

Record the location information for the drive.

Note:

The location information is in either of these forms:

0:0:5:0

In this example, 0 is the SCSI host number, 0 is the SCSI bus, 5 is the SCSI target ID, and 0
is the logical unit number (LUN).

0/00-0E-02

In this example, 0 is the SCSI host number, 00 is the I/O adapter (IOA) SAS port, 0E is the
expander port, and 02 is the device port.

Type

iprconfig

on the command line and press

Enter

. The IBM Power RAID Configuration Utility

display is shown.

Select Display hardware status from the IBM Power RAID Configuration Utility display. Press

Enter

. The Display Hardware Status screen displays as shown in Figure 85 and Figure 86 on page

87.

Kernel Messages Log

Select one of the following:

1. View most recent ipr error messages
2. View ipr error messages
3. View all kernel error messages
4. View iprconfig error messages
5. Set root kernel message log directory
6. Set default editor
7. Restore defaults
8. View ipr boot time messages

Selection:
e=Exit

Figure 84. Kernel Messages Log

Display Hardware Status

Type option, press Enter.

1=Display hardware resource information details

OPT Name

PCI/SCSI Location

Description

Status

--- ------ -------------------------- ------------------------- ----------------

0000:01:00.0/0:

PCI-E SAS RAID Adapter

Operational

0000:01:00.0/0:0:0:0

Advanced Function SSD

Active

0000:01:00.0/0:0:1:0

Advanced Function SSD

Active

0000:01:00.0/0:0:2:0

Advanced Function SSD

Active

0000:01:00.0/0:0:3:0

Advanced Function SSD

Active

0000:01:00.0/0:0:4:0

Advanced Function SSD

Active

0000:01:00.0/0:0:5:0

Advanced Function SSD

Failed

0000:01:00.0/0:0:6:0

Advanced Function SSD

Active

0000:01:00.0/0:0:8:0

Enclosure

Active

0000:01:00.0/0:0:9:0

Enclosure

Active

0001:01:00.0/1:

PCI-E SAS RAID Adapter

Operational

0001:01:00.0/1:0:3:0

Advanced Function SSD

Remote

0001:01:00.0/1:0:4:0

Advanced Function SSD

Remote

0001:01:00.0/1:0:5:0

Advanced Function SSD

Remote

More...

e=Exit

q=Cancel

r=Refresh

t=Toggle

f=PageDn

b=PageUp

Figure 85. Example Display Hardware Status

Disk drives or solid-state drives

Содержание Power System 5148-22L













































































































































































































Результаты поиска

Содержание Power System 5148-22L

Отзывы:

Похожие инструкции для Power System 5148-22L

Бренды по названию

Популярные бренды

IBM Power System 5148-22L, Руководство пользователя

Результаты поиска

Содержание Power System 5148-22L

Отзывы:

Похожие инструкции для Power System 5148-22L

Бренды по названию

Популярные бренды