IBM H3V Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 141

IBM H3V Скачать руководство пользователя страница 40

The SCD Dot turns off when you obtain a dump (by using ITDT or a SCSI
command) or update the drive firmware.

Note:

If the drive dump is stored in RAM memory (SCD Dot on solid), the dump
will be lost when you turn OFF the power or reset the drive.

Status Lights

The status lights (

2

,

3

in “Front panel of the drive” on page 1-2) are

light-emitting diodes (LEDs) that provides information about the state of the drive.
The Ready status light is green and the Fault status light is amber, and (when lit)
solid or flashing.

Mode

SCD

Ready LED (green)

Fault LED (amber)

Operational

blank

On

Off

Activity (tape movement)
in Operational Mode

blank

Flashing

Off

Maintenance

solid character

Flashing

On

Executing Maintenance
Selection

flashing character

Off

On

Error Condition

solid character

Off

Flashing

Power-On / Reset
Initialization

random segments

Off

On

Table 3-1 lists the conditions of the status lights and Single-character Display (SCD)
and provides an explanation of what each condition means.

Table 3-1. Meaning of Status Lights and Single-character Display (SCD)

If the green

Ready Status

Light is...

and the amber

Fault Status

Light is...

and the SCD

is...

and the SCD Dot

is...

Meaning

Off

Off

Off

Off

The drive has no power or is powered off.

On

Off

Off

Off

The drive is powered on and in an idle state.

Flashing

(once per

second)

Off

Off

Off

The drive is reading from the tape, writing to
the tape, rewinding the tape, locating data on
the tape, loading the tape, or unloading the
tape.

Flashing

(once per

second)

Off

Off

Off

If the drive contains a cartridge during the
power-on cycle, the drive completes POST and
slowly rewinds the tape (the process may take
up to ten minutes). The light stops blinking
and becomes solid when the drive completes
the recovery and ejects the cartridge.

Off

On

Displaying an

error code or

Maintenance

Mode Function

On/Off

The drive is displaying error code(s) from the
error code log on the SCD. For more
information, see “Function Code 9: Display
Error Code Log” on page 3-15 and
Appendix A, “Error Codes and Messages,” on
page A-1.

3-2

TS2230 Tape Drive Setup, Operator and Service manual

«
...
38
39
40
41
42
...
»

Содержание H3V














































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды