background image

Table 10. Rack space requirements for the Elastic Storage System 3000
Minimum rail length

Maximum rail depth

670 mm (26.38 in.)

870 mm (34.25 in.)

Service clearance for Elastic Storage System 3000
The service clearance area is the area around the rack which is needed for the authorized service

representatives to service the enclosure as shown in the sample illustration in the Figure 12 on page 32.

Figure 12. Sample illustration to show space around the rack

For Elastic Storage System 3000, use the recommended measurements that are given in the Table 11 on

page 32.

Table 11. Service clearance requirements
Front

1

Back

1200 mm (47 in.)

1000 mm (39 in.)

1

Storage racks require larger service clearances in the front of the rack.

For more information on the layout of the room, see Computer room layout
See the Site preparation and physical planning section to help you prepare your physical site for the

installation of Elastic Storage System 3000.

Additional space requirements

Ensure that these additional space requirements, as shown in Table 12 on page 33, are available around

the enclosures.

32  IBM Elastic Storage System 3000: Hardware Planning and Installation Guide

Содержание ESS 3000













































































































Отзывы: