IBM Elastic Storage System 3200 Скачать руководство пользователя страница 80

Страница: 80 / 156

Netmask: 255.255.255.0
BMC Network IPs:

Subnet: 10.0.0.0/24

IP Address: 10.0.0.1 (C11-T2)

IP Address: 10.0.0.100 (HMC1)

Netmask: 255.255.255.0
POWER9 EMS

Table 21. EMS management connections
Physical interface

Logical interface

Port C11-T1

mgmt

Port C11-T2

fsp

Left canister best practices

Ensure that each IP in the worksheet is on the same subnet. Recommended subnet is /24

(255.255.255.0).
Management Network IPs:

Subnet: 192.168.45.0/24

IP Address: 192.168.45.50

Netmask: 255.255.255.0
BMC Network IPs:

Subnet: 10.0.0.0/24

IP Address: 10.0.0.120 (BMC)

Netmask: 255.255.255.0
• Logical interface: mgmt
• Physical interface: Port 1

Right canister best practices

Ensure that each IP in the worksheet is on the same subnet. Recommended subnet is /24

(255.255.255.0).
Management Network IPs:

Subnet: 192.168.45.0/24

IP Address: 192.168.45.51

Netmask: 255.255.255.0
BMC Network IPs:

Subnet: 10.0.0.0/24

IP Address: 10.0.0.121 (BMC)

Netmask: 255.255.255.0
• Logical interface: mgmt
• Physical interface: Port 1

Prerequisites for installation completion by SSR

Customers must fill the Installation worksheet for the SSR to start installation. This process must be done

by using the Technical Delivery Assessment (TDA) process. The worksheet describes the IP addresses

that the SSR sets on each node. If the worksheet is not completed, the SSR might confirm with the

personnel at the data center and use default IP addresses listed.
Racked or rackless installation:

62 IBM Elastic Storage System 3200: Hardware Planning and Installation Guide

Содержание Elastic Storage System 3200





























































































































































Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды

IBM Elastic Storage System 3200, Руководство по планированию и установке оборудования

Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды