Ethernet
connector
Use
this
connector
to
connect
the
server
to
a
network.
Serial
2
connector
Connect
a
9-pin
serial
device
to
this
connector.
Ethernet
link
status
LED
This
LED
is
on
the
Ethernet
connector
on
the
back
of
the
server.
When
this
LED
is
lit,
it
indicates
that
there
is
an
active
connection
on
the
Ethernet
port.
Ethernet
transmit/receive
activity
LED
This
LED
is
on
the
Ethernet
connector.
When
this
LED
is
lit,
it
indicates
that
there
is
activity
between
the
server
and
the
network.
Server
power
features
When
the
server
is
connected
to
an
ac
power
source
but
is
not
turned
on,
the
operating
system
does
not
run,
and
all
core
logic
is
shut
down;
however,
the
server
can
respond
to
remote
requests
to
turn
on
the
server.
The
power-on
LED
flashes
to
indicate
that
the
server
is
connected
to
an
ac
power
source
but
is
not
turned
on.
Turning
on
the
server
Approximately
20
seconds
after
the
server
is
connected
to
ac
power,
the
power-control
button
becomes
active,
and
one
or
more
fans
might
start
running
to
provide
cooling
while
the
server
is
connected
to
power.
You
can
turn
on
the
server
and
start
the
operating
system
by
pressing
the
power-control
button.
The
server
can
also
be
turned
on
in
any
of
the
following
ways:
v
If
a
power
failure
occurs
while
the
server
is
turned
on,
the
server
will
restart
automatically
when
power
is
restored.
v
If
your
operating
system
supports
the
Wake
on
LAN
feature,
the
Wake
on
LAN
feature
can
turn
on
the
server.
Note:
When
4
GB
or
more
of
memory
(physical
or
logical)
is
installed,
some
memory
is
reserved
for
various
system
resources
and
is
unavailable
to
the
operating
system.
The
amount
of
memory
that
is
reserved
for
system
resources
depends
on
the
operating
system,
the
configuration
of
the
server,
and
the
configured
PCI
options.
Turning
off
the
server
When
you
turn
off
the
server
and
leave
it
connected
to
ac
power,
the
server
can
respond
to
remote
requests
to
turn
on
the
server.
While
the
server
remains
connected
to
ac
power,
one
or
more
fans
might
continue
to
run.
To
remove
all
power
from
the
server,
you
must
disconnect
it
from
the
power
source.
Some
operating
systems
require
an
orderly
shutdown
before
you
turn
off
the
server.
See
your
operating-system
documentation
for
information
about
shutting
down
the
operating
system.
32
xSeries
100
Type
8486:
Installation
Guide
Содержание E Server x 100 Series
