IBM DTTA-351010 - Deskstar 10.1 GB Hard Drive Скачать руководство пользователя страница 16

Страница: 16 / 188

3.2

Data Sheet

Figure 2. Mechanical Positioning Performance

DTTA-35xxxx

DTTA-37xxxx

Media Transfer Rate (Mb/sec)

92.2 - 163.7

111.6 - 175.6

Interface Transfer Rate (MB/sec)

16.6 (PIO Mode-4)

33.3 (Ultra DMA/33)

16.6 (PIO Mode-4)

33.3 (Ultra DMA/33)

Data Buffer Size (KB)

464

Rotational Speed (RPM)

5400

7200

Average Latency (msec)

5.56

4.17

Recording Density (Kbpi)

196.1 max

178.1 max

Track Density (TPI)

13,700

Areal Density (Gb/sq.in.)

2.687 max

2.440 max

Number of Zone

Number of Data Disks

5/4/3/3/2/2/1

5/5/4

Number of Data Heads

10/8/6/5/4/3/2

10/9/7

Servo Method

Embeded Sector Servo

O E M Specifications for DTTA-3xxxxx

Содержание DTTA-351010 - Deskstar 10.1 GB Hard Drive





























































































































































































Результаты поиска

Содержание DTTA-351010 - Deskstar 10.1 GB Hard Drive

Отзывы:

IBM DTTA-351010 - Deskstar 10.1 GB Hard Drive, Технические характеристики, Страница: 16 / 188

Результаты поиска

Содержание DTTA-351010 - Deskstar 10.1 GB Hard Drive

Отзывы: