![background image](http://html1.mh-extra.com/html/ibm/deskstar-14gxp/deskstar-14gxp_quick-installation-manual_3801073002.webp)
IBM storage products
Page 2
IBM Hard Disk Drive Technical Support Center version 3.0
Attaching the drive
1. Turn off the computer, unplug the power cord, and
open the case.
2. Match pin 1 of the 40-pin cable to pin 1 of the drive
interface connector. Pin 1 is usually denoted by a
stripe along the edge of the cable.
3. Insert a power plug in either the 3- or 4-pin power
connector.
Mounting the Drive
1. Mount the drive securely, using the appropriate
brackets or rails, in any axes, using four 6-32 UNC
metric screws in either bottom or side mounting
holes.
2. The maximum screw insertion depth for the bottom
mounting is 4 mm and for side mounting 4.5 mm.
Configuring your computer
1. If your computer has a plug-in IDE card with a drive
installation procedure, follow the manufacturer’s in-
structions.
2. Plug in the power cord and power on your com-
puter. Your computer may detect a configuration
change and prompt you to proceed to the Setup
screen. If so, proceed to step 4.
3. If your computer does not prompt you to reconfig-
ure, enter your computer’s Setup, typically by key
selection or keyboard combinations during power-on
or during a reboot. Refer to your computer’s docu-
mentation for the proper key sequence. If the com-
puter fails to boot up, power off, remove the new hard
drive and reconfigure your system to its original con-
figuration. Reboot and enter your computer’s Setup.
Follow the directions in step 4, then reattach the new
hard drive.
4. Select “Auto Detect” if your computer Setup sup-
ports this feature. If your computer does not Auto
Detect the drive, select the appropriate UDT (User
Definable Type) for the model being installed.
Then run Disk Manager.
9.1GB
63
15
16,383
clip version
10.1GB
63
15
16,383
DTTA-371010
12.9GB
63
15
16,383
DTTA-371290
14.4GB
63
15
16,383
DTTA-371440
Capacity
Sector
/Track
Heads
Cylinders
IBM model
number
Running Disk Manager
1. Insert the Ontrack diskette and reboot your
computer.
2. Type DM and press [ENTER] to run Disk Manager.
3. Under “Select an Installation Option”, select (E)asy
Disk Installation.
4. Select a drive for installation; Disk Manager will
partition and format the drive.
5. A status dialog will indicate a successful instal-
lation.
If, after complete installation, your system will not
boot up, recheck all settings. If it still will not boot up,
remove the new drive to return to your original
configuration and contact technical support.
®
© International Business Machines Corporation 2002
www.ibm.com/harddrive
IBM Hard Disk Drive Technical Support Center
Dept. D8M
3605 Highway 52 North
Rochester, MN 55901
Telephone: 888.IBM.5214 or 507.253.4110
Fax: 507.253.3748
E-mail: [email protected]
Singapore Technical Support Center
Telephone: 65.840.9292
E-mail: [email protected]
IBM Systems Storage Division
5600 Cottle Road
San Jose, CA 95193
www.ibm.com/storage
Asia-Pacific Headquarters: 65.320.1234
European Headquarters: 44.01.705.561.871
Japan Sales Branch Office: 81.46645.1039
Printed in the United States of America
01-99
All Rights Reserved
IBM is the registered trademark of International Business Machines Corporation.
Other company, product, and service names may be trademarks or service marks of others.
Produced by the IBM Hard Disk Drive Technical Support Center.
OEM Hard Disk Drive Specifications for DTTA-3xxxxx, revision 2.0
Product Description data represents IBM’s design objectives and is provided for
comparative purposes; actual results may vary based on a variety of factors. This product
data does not constitute a warranty. Questions regarding IBM’s warranty terms or
methodology used to derive this data should be referred to the IBM Hard Disk Drive
Technical Support Center. Data subject to change without notice.
Date:26 November 2002